Brand:

ifm SI5010 Flow Monitor with IO-Link, PNP Output, 300 bar

Description

ifm SI5010 overview

The ifm SI5010 adds IO-Link communication to the flow monitor housing. Pin 4 works either as a PNP switching output or as the IO-Link line, so the same sensor can run on a conventional input or on an IO-Link master that reads process data and lets the engineer set parameters remotely. The pressure rating is 300 bar, with a CRN maximum allowable working pressure of 208 bar. Ordering description: SID10ADBFPKG/US-100.

Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. We list this device so that maintenance, procurement and project teams can quote the exact part number against the manufacturer data.

Key features of the SI5010

  • IO-Link revision 1.1 at COM2 38.4 kBaud, device ID 54, minimum process cycle time 3 ms.
  • Switching output PNP, normally open or closed, 250 mA, with pulsed short-circuit protection.
  • Liquids 3 to 300 cm/s and gases 200 to 3000 cm/s setting ranges.
  • Operating voltage 18 to 36 V DC, IP 65 and IP 67 protection.
  • Required master port type A; two analogue and two binary process data.

SI5010 technical specifications

Parameter Value from the manufacturer datasheet
Number of inputs and outputs Number of digital outputs: 1
Process connection threaded connection M18 x 1,5 internal thread
Media Liquids; Gases
Medium temperature [°C] -25…80
Pressure rating 300 bar 30 MPa
Operating voltage [V] 18…36 DC
Current consumption [mA] less than 60
Min. insulation resistance [MΩ] 100; (500 V DC)
Protection class III
Reverse polarity protection yes
Power-on delay time [s] 10
Total number of outputs 1
Output signal switching signal; IO-Link; (configurable)
Electrical design PNP
Number of digital outputs 1
Output function normally open / normally closed; (parameterisable)
Short-circuit protection yes
Overload protection yes
Probe length L [mm] 45
Setting range [cm/s] 3…300
Greatest sensitivity [cm/s] 3…100
Repeatability [cm/s] 1…5
Note on repeatability for water 5…100 cm/s; 25 °C
Temperature drift [cm/s x 1/K] 0.1; (for water 5…100 cm/s; 10…70 °C)
Temperature gradient [K/min] 300
Switch point accuracy [cm/s] ± 2…± 10; (for water 5…100 cm/s; 25 °C; Factory setting)
Hysteresis [cm/s] 2…5; (for water 5…100 cm/s; 25 °C; Factory setting)
Response time [s] 1…10
Communication interface IO-Link
Transmission type COM2 (38,4 kBaud)
IO-Link revision 1.1
SDCI standard IEC 61131-9
Profiles Smart Sensor – SSP 0 Generic Profiled Sensor
SIO mode yes
Required master port type A
Process data analogue 2
Process data binary 2
Min. process cycle time [ms] 3
Supported DeviceIDs Type of operation DeviceID
Ambient temperature [°C] -25…80
Storage temperature [°C] -25…100
Protection IP 65; IP 67
Shock resistance DIN IEC 60068-2-27 50 g (11 ms)
Vibration resistance DIN EN 60068-2-6 20 g (55…2000 Hz)
MTTF [years] 298
Weight [g] 248.5
Housing cylindrical
Dimensions [mm] Ø 50 / L = 113

All values above are taken from the manufacturer datasheet for the SI5010. Ranges are written with three dots, for example 18…30 means 18 to 30. Where a limit depends on the medium or the installation, the datasheet condition applies.

Typical applications in oil and gas, utilities, water and manufacturing

Typical uses in the region include protecting pumps and heat exchangers against dry running or loss of cooling water, proving circulation in lube-oil, seal-water and chilled-water loops, and detecting flow of liquids or gases in utility headers on process skids, compressor packages and water treatment plants.

In Oman and the wider GCC, flow monitoring devices like the SI5010 are found in pump protection, cooling-water proving and utility flow supervision. Hot ambient conditions, dust and long cable runs make a sensor with clear local indication and stable outputs valuable, because it shortens fault finding for the shift technician. Check the ambient and medium temperature limits in the table above against the actual site conditions before selecting the device.

Selection and compatibility notes for the SI5010

Choose the SI5010 when the plant already uses an IO-Link master and parameters need to be backed up or cloned during sensor replacement. If you only need a basic contact, the SI5000 is simpler. The sensor needs a class A master port, so check the port type on the master card.

When you match this device to an existing loop, compare the supply voltage, output type, connector and process connection with the installed device, and confirm that the control system input accepts the signal. Because the part number identifies one exact version in the family, a similar-looking sibling can differ in output polarity, range or thread, and it is better to quote the exact designation than a family name.

Installation and commissioning

The probe must sit in the flow with its sensing end fully immersed in the medium, in a straight pipe section away from valves, elbows and pumps, so that the flow profile is stable. Use the tightening torque shown on the datasheet drawing and a suitable process adapter. After installation, set the switch point or analogue range under real flow conditions rather than relying on factory settings, and note the setting in the maintenance log.

Before power-up, check the wiring against the connection diagram in the datasheet, and after power-up allow any start-up delay listed in the table to elapse before judging the output. Document the settings made on site together with the serial number so that a replacement can be configured identically.

Maintenance and service

Check the probe for deposits, scale or oil film at the intervals the process demands, because coating on a probe can shift the response. Verify the switch point during planned shutdowns, inspect the O-ring and the M12 connector for damage, and keep a spare cable on the shelf.

Related products and ordering notes

Related ifm devices already listed in the Seven Star catalogue can be found through the brand page. When you request this device, please state the quantity, the required delivery location and whether a datasheet copy is needed. If the application is critical, tell us the process medium, pressure and temperature so the engineer can check the data before the quotation is prepared.

Frequently asked questions

  • What is the ifm SI5010? The ifm SI5010 is a flow monitor with IO-Link and a PNP output. The ifm SI5010 adds IO-Link communication to the flow monitor housing.
  • What supply and protection rating does the SI5010 have? According to the manufacturer datasheet the SI5010 operates from 18…36 DC and has protection III.
  • Is the SI5010 still available from the manufacturer? The manufacturer datasheet does not carry a phase-out or archive notice, but availability changes over time, so ask us to confirm stock and lead time when you send the RFQ.
  • Does Seven Star LLC supply the SI5010 in Oman? Yes, Seven Star LLC quotes the SI5010 for projects and maintenance in Oman and the GCC. Send the part number SI5010 and the quantity and we will respond with availability.
  • How do I get a quotation for the SI5010? Use the RFQ form on this page with the part number SI5010, the quantity and your delivery location. We will reply with a quotation after checking availability.

Documents and quotation

The manufacturer datasheet is attached to this page where the file is available, and it is the reference for every value shown here. To order, send the RFQ with part number SI5010 and the quantity required, together with the delivery location and any application details. Our team will confirm availability and respond with a quotation.

Datasheets & Documents
  • PDF Datasheet ifm SI5010 Flow Monitor with IO-Link, PNP Output, 300 bar Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.

Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.

ifm company profile

Founded 1969, Essen, Germany
Founders Robert Buck and Gerd Marhofer
Headquarters Essen, Germany
Ownership Family-owned
Product families Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters

Milestones

  • 1969: ifm is founded in Essen.
  • 2001: The founders' sons take over management.

ifm sensors listed on this page

ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:

  • O1D100: laser distance sensor for position and distance measurement
  • PN7093: pressure sensor with local display
  • NG5021: inductive proximity sensor with NAMUR output

Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.

ifm products we list

Family Examples
Inductive Proximity Sensors NG5021 Inductive NAMUR Proximity Sensor
Laser Distance, LiDAR & Radar Sensors O1D100 Laser Distance Sensor
Pressure Instrumentation PN7093 Pressure Sensor with Display

Ordering ifm sensors: what we need

Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.

Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.

FAQ

Questions about the ifm SI5010 Flow Monitor with IO-Link, PNP Output,

Answers from our engineering team on installation, compatibility and integration.

01What is the ifm SI5010?
The ifm SI5010 is a flow monitor with IO-Link and a PNP output. The ifm SI5010 adds IO-Link communication to the flow monitor housing.
02What supply and protection rating does the SI5010 have?
According to the manufacturer datasheet the SI5010 operates from 18...36 DC and has protection III.
03Is the SI5010 still available from the manufacturer?
The manufacturer datasheet does not carry a phase-out or archive notice, but availability changes over time, so ask us to confirm stock and lead time when you send the RFQ.
04Does Seven Star LLC supply the SI5010 in Oman?
Yes, Seven Star LLC quotes the SI5010 for projects and maintenance in Oman and the GCC. Send the part number SI5010 and the quantity and we will respond with availability.
05How do I get a quotation for the SI5010?
Use the RFQ form on this page with the part number SI5010, the quantity and your delivery location. We will reply with a quotation after checking availability.