Brand:

Flowserve Limitorque SMB-2 Multi-Turn Electric Actuator

Description

Flowserve Limitorque SMB-2 Limitorque multi-turn electric actuator overview

The SMB-2 is a size in the Limitorque SMB series of multi-turn electric valve actuators made by Flowserve. The SMB range is built around a rugged cast iron or ductile iron housing and a double-reduction gear set, with a helical stage and a worm stage, which the manufacturer positions as the choice for valve duties where service life and strength matter more than anything else. The SMB-2 is rated for a maximum torque of 1,950 ft-lb (2,644 Nm) and a maximum stem thrust of 70,000 lb (311 kN), with an output speed range of 10-250 rpm. Those figures are commercial service ratings, and the maximum torque available is output speed dependent.

In practice the SMB-2 is selected when a rising-stem gate or globe valve needs a motor operator that can seat reliably, protect the valve against overload, and keep working for decades with routine checks. Quarter-turn valves such as ball, plug and butterfly are normally motorized by mounting the actuator on a Limitorque gearbox, and the manufacturer lists HBC and WG worm gearboxes for that purpose and V and SR gearboxes for multi-turn work. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.

Key features of the SMB-2

  • Double-reduction gearing with an alloy bronze worm gear, an alloy steel worm and heat-treated steel helical gears, running in a sealed gear case that is filled with grease at the factory.
  • A hammer-blow feature that lets the motor reach full speed before the load is picked up, so the SMB-2 applies its force to the valve shaft at full motor speed.
  • Automatic torque limiting that de-energizes the motor when the valve meets an obstruction, protecting stems, discs and seats.
  • A geared limit switch with 16 contacts in 4 trains, plus a torque switch with one SPST contact per direction, both rated at 300 volts and 6 amps resistive.
  • A declutchable handwheel for manual operation during a power interruption, and an insert stem nut that allows the actuator to be moved to another valve without major disassembly.
  • Weatherproof construction as standard, with explosion-proof, Navy Class A and nuclear versions offered by the manufacturer.

Flowserve Limitorque SMB-2 technical specifications

Model Flowserve Limitorque SMB-2 multi-turn electric actuator
Series SMB (spring-compensated SB and SBD variants available)
Maximum torque rating 1,950 ft-lb (2,644 Nm), commercial service
Maximum thrust rating 70,000 lb (311 kN)
Output speed range 10-250 rpm
Two-piece stem nut, maximum threaded stem 3.5 in
Two-piece nut, maximum bore and keyway 2.875 in with 3/4 x 1/4 key (73.0 mm with 20 x 6 key)
One-piece drive sleeve, maximum threaded stem 3.875 in
One-piece drive sleeve, maximum bore and keyway 3.250 in with 3/4 x 1/4 key (82.0 mm with 22 x 7 key)
Available AC motors, 4-pole (ft-lb) 40, 60, 80
Available AC motors, 2-pole (ft-lb) 40, 60, 80
Approximate weight, largest motor 755 lb (342 kg)
Weight adder for SB spring package 270 lb (122 kg)
Weight adder for SBD spring package 325 lb (147 kg)
Mounting pilot 7.000 in (177.8 mm), length 0.188 in
Mounting holes 3/4-10 UNC x 1.13 in
Bolt circle 8 holes at 45 degrees on a 11.75 in (298.45 mm) bolt circle
Mounting base diameter 13.5 in (342.9 mm)
Standard enclosure Weatherproof, suitable for NEMA 4
Ambient temperature rating -20 to 150 degrees F (-29 to 66 degrees C)
Motor power supply 3-phase 230, 460 or 575 V at 60 Hz; 380 or 415 V at 50 Hz
Nominal motor duty 15 minutes
Motor insulation Class F standard
Gear case lubricant MOV long-life EP grease, NLGI grade 0
Seals Viton

Weights in the table are those the manufacturer quotes for the largest motor of the size, with the standard handwheel, a 4-train geared limit switch, an iron control compartment cover and no integral reversing controls package. Motor sizes are written in the manufacturer notation, where a rating such as 60/4P means 60 foot-pounds on a four-pole motor, which runs at 1800 rpm on 60 Hz or 1500 rpm on 50 Hz supplies.

Typical SMB-2 applications in Oman and the GCC

The SMB series has a long record in nuclear power, naval and heavy process duty, and the same construction suits the plant types found across Oman and the Gulf. Typical places to specify a SMB-2 include the following.

  • Oil and gas wells, platforms, pipelines, petroleum terminals and tank farms, where an actuator can sit outdoors for long periods at high ambient temperature.
  • Refineries, petrochemical and chemical plants, including hydrocarbon processing units and heavy duty services such as cokers.
  • Power stations and steam distribution systems, where isolation and block valves need predictable torque and thrust.
  • Water transmission pipelines, wastewater treatment, dams and flood gates, where large gate and butterfly valves are motorized through gearboxes.
  • Industrial plants such as steelworks, mines, ore processing and pulp and paper mills.

Selecting and matching the SMB-2

Sizing starts from the valve. Work out the seating and unseating torque or thrust at the highest differential pressure, then choose the smallest SMB size whose rating exceeds it with margin. The SMB-2 covers up to 1,950 ft-lb of torque and 70,000 lb of thrust, so a valve that needs more should move up a size and one that needs much less should move down so that the torque switch has a sensible working range. Stem size matters as well: the two-piece stem nut accepts a threaded stem up to 3.5 in, while the one-piece drive sleeve accepts up to 3.875 in, and the bore and keyway limits are given in the table.

Motor choice follows speed and supply. Four-pole and two-pole motors are available for the SMB-2 in the ratings shown above, and the output speed is set by the gear ratio, so a faster valve stroke is bought with a different ratio and not by an oversized motor. For quarter-turn valves the SMB-2 is mounted on a HBC or WG gearbox, and for high-speed or high-temperature torque-seated gate and globe valves the manufacturer offers the SB single-compensating and SBD double-compensating spring packages with the same electrical options and mounting bases as the standard SMB. Controls are offered as NCU, a no controls actuator, or INT, which adds a transformer and reversing contactor, along with position transmitters, space heaters, breathers and drains.

Installing and commissioning the SMB-2

Before mounting the SMB-2, confirm the actuator size, order number and serial number on the nameplate fixed to the back of the housing, opposite the limit switch compartment. The base must match the valve flange: 3/4-10 UNC x 1.13 in with 8 holes at 45 degrees on a 11.75 in (298.45 mm) bolt circle, as listed in the table. Keep the stem clean and lubricated, fit the correct drive sleeve or stem nut, and tighten the bolts evenly. The gear case should hold grease at the correct level before the first operation, particularly after a long storage period.

Commissioning consists of setting the torque switch for each direction, setting the geared limit switch rotors at the open and closed positions, checking the position indicator and any potentiometer, and verifying motor rotation and wiring against the diagram supplied with the actuator. The handwheel is used to position the valve near mid-travel while the limit switch is adjusted, so that motor operation is never first tried against a hard stop.

Maintenance of the SMB-2

The manufacturer recommends a routine maintenance check at least every 18 months, more often when the duty is heavy or the environment is harsh. The check includes inspecting the limit switch compartment for moisture, wiping electrical contacts clean, confirming that terminal connections are tight, cleaning and inspecting the gasketed cover surfaces, looking at shaft penetrations for seal leakage and megger testing the motor, where one megohm or higher is considered normal.

For lubrication, inspect the main gear case every 18 months or 500 cycles, whichever comes first, and the geared limit switch every 36 months or 1,000 cycles. The drive sleeve top bearing is lubricated every 6 months through its pressure fitting. The factory fill is an NLGI grade 0 grease suitable for continuous ambient temperatures from minus 20 to 150 degrees F. Slight weeping around shaft seals is common after storage and is not by itself a reason to replace a seal.

Related products and ordering notes for SMB-2

Neighbouring SMB sizes, the SB and SBD spring-compensated variants, Limitorque gearboxes and replacement control components are quoted separately. When you ask for a quotation on the SMB-2, include the valve type, maximum differential pressure, required stroke time, supply voltage and frequency, enclosure or hazardous area class, and whether integral controls, a potentiometer or a mechanical dial position indicator are needed. For a replacement, the order number and serial number from the existing nameplate allow the configuration to be matched correctly.

SMB-2 frequently asked questions in brief

The SMB-2 delivers up to 1,950 ft-lb of torque and 70,000 lb of thrust. It accepts a threaded stem of up to 3.5 in with the two-piece nut, weighs about 755 lb with its largest motor, and mounts on a 13.5 in (342.9 mm) base. Spring compensation is available as SB and SBD. Detailed answers appear in the questions below this description.

Documents and quotation

The manufacturer brochure for the SMB series is attached to this page as the datasheet for the SMB-2, and the installation, operation and maintenance manual covers wiring, torque switch setting and lubrication in detail. To request a quotation, send the part number SMB-2 with the quantity, delivery location and any special requirements, and the team will reply with availability and lead time. No prices are published on this page.

Other Models in the Limitorque SMB Range

Seven Star LLC supplies models from the Limitorque SMB range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Flowserve Limitorque SMB-000 Multi-Turn Electric ActuatorElectric ActuatorsView details
Flowserve Limitorque SMB-0 Multi-Turn Electric ActuatorElectric ActuatorsView details
Flowserve Limitorque SMB-1 Multi-Turn Electric ActuatorElectric ActuatorsView details
Flowserve Limitorque SMB-2 Multi-Turn Electric ActuatorElectric ActuatorsYou are viewing this model
Flowserve Limitorque SMB-3 Multi-Turn Electric ActuatorElectric ActuatorsView details
Flowserve Limitorque SMB-4 Multi-Turn Electric ActuatorElectric ActuatorsView details
Flowserve Limitorque SMB-5 Multi-Turn Electric ActuatorElectric ActuatorsView details
Datasheets & Documents
  • PDF Datasheet Flowserve Limitorque SMB-2 Multi-Turn Electric Actuator Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Flowserve is the American flow control company for pumps, valves, mechanical seals and valve automation, known through brands such as Durco, Worthington, Byron Jackson, Valtek, Limitorque, Worcester, Logix and Argus. It was formed on 22 July 1997 by the merger of equals of Durco International and BW/IP, whose heritage reaches back to Simpson & Thompson (1790) and Byron Jackson (1872). Flowserve Corporation is headquartered in Irving, Texas, and listed on the New York Stock Exchange.

Seven Star LLC sources and supplies Flowserve pumps, seals, control valves, ball valves, actuators and positioners for process plants in Oman, working from the nameplate data and the manufacturer's documentation.

Flowserve company profile

Formed 22 July 1997, merger of Durco International and BW/IP
Heritage companies Simpson & Thompson, later Worthington Simpson (1790); Byron Jackson (1872); Duriron foundry, later Durco (1912)
Headquarters Irving, Texas, USA
Ownership Flowserve Corporation, public company (NYSE: FLS)
Product families API and ANSI process pumps, Durco and Worcester ball and plug valves, Durco TX3 triple-offset and Valtek butterfly and globe control valves, Limitorque electric actuators, Logix positioners, mechanical seals

Milestones

  • 1790: Thomas Simpson founds Simpson & Thompson, a predecessor of Worthington Simpson pumps.
  • 1872: Byron Jackson is founded, a root of BW/IP.
  • 1912: The Duriron foundry, later Durco, is launched.
  • 1997: Durco International and BW/IP merge on 22 July to form Flowserve, listed on the NYSE as FLS.

Flowserve product families listed here

Flowserve pumps on this page are the Durco Mark 3 ANSI process pump and the ECPJ vertical sump pump built to API 610 type VS4. Sealing products are the ISC2 cartridge mechanical seal to API 682 and DuraClear barrier fluid for dual seal systems. Flowserve valves include the Valtek Mark One globe control valve, Argus floating and trunnion-mounted ball valves (EK71, FK79, FK76M) and Durco Microfinish ball valves. Automation is covered by Limitorque MX and L120 multi-turn electric actuators, the Rotadisk RD and RDF pneumatic actuator and the Logix 3800 digital positioner.

Where Flowserve equipment is used

Mark 3 pumps handle acids, caustic, solvents and utilities in chemical and petrochemical units. VS4 sump pumps drain pits and collection tanks. Valtek control valves and Argus ball valves are found in refining, gas processing, power and desalination, and Limitorque actuators operate gate and globe valves on pipelines, tank farms and water networks across the GCC.

Flowserve products we list

Family Examples
Ball Valves Argus EK71 End-Entry Floating Ball Valve, Argus FK76M Trunnion Mounted Ball Valve, Argus FK79 Floating Ball Valve, Durco Microfinish Ball Valves, Worcester Series 44 Three-Piece Ball Valve
Pumps DS-4614-5-F DuraClear Barrier Fluid, Durco Mark 3 ANSI Process Pump, ECPJ 25-200-R API 610 VS4 Vertical Sump Pump, ISC2 API 682 Cartridge Mechanical Seal
Control Valves Valtek Mark 100 Ultra-Capacity Globe Control, Valtek MaxFlo 4 Eccentric Rotary Plug Control, Valtek Valdisk High-Performance Butterfly, Valtek Mark One Globe Control Valve
Valve Actuators Limitorque L120 Multi-Turn Electric Actuator, Rotadisk RD and RDF Pneumatic Actuator, Limitorque MX Multi-Turn Actuator
Butterfly Valves Durco TX3 Triple Offset Butterfly Valve
Valve Positioners Logix 3800 Digital Positioner

Ordering Flowserve parts: what we need

The serial number on the nameplate is the key to Flowserve records for a pump, valve or actuator. Please add the following by product type:

  • Pumps: size and model, impeller diameter, materials, seal arrangement, and the part name and item number from the sectional drawing
  • Mechanical seals: seal type and size, drawing or part number, materials code, pumped fluid and flush plan
  • Valves: size, pressure class, body and trim materials, end connections, and the actuator and positioner model
  • Limitorque actuators: unit size, order and serial number, supply voltage, wiring diagram number

Facts checked against Flowserve's SEC filings and published company histories, October 2026.

FAQ

Questions about the Flowserve Limitorque SMB-2 Multi-Turn Electric

Answers from our engineering team on installation, compatibility and integration.

01What torque and thrust does the SMB-2 provide?
The manufacturer lists the SMB-2 at a maximum torque of 1,950 ft-lb (2,644 Nm) and a maximum thrust of 70,000 lb (311 kN) in commercial service, with output speeds of 10-250 rpm. Torque available depends on the output speed.
02Which motors can be fitted to the SMB-2?
The brochure lists 4-pole motors of 40, 60, 80 ft-lb and 2-pole motors of 40, 60, 80 ft-lb for the SMB-2, on supplies of 230, 460 or 575 V at 60 Hz or 380 or 415 V at 50 Hz.
03What stem size does the SMB-2 accept?
The two-piece stem nut accepts a threaded stem up to 3.5 in and a bore of 2.875 in with 3/4 x 1/4 key (73.0 mm with 20 x 6 key). The one-piece drive sleeve accepts a threaded stem up to 3.875 in and a bore of 3.250 in with 3/4 x 1/4 key (82.0 mm with 22 x 7 key).
04Can the SMB-2 be supplied with spring compensation?
Yes, the brochure lists SB single-compensating and SBD double-compensating packages for this size, adding about 270 lb and 325 lb respectively. They suit high-speed or high-temperature torque-seated valves.
05How do I request a quotation for the SMB-2?
Send an RFQ with the part number SMB-2, the quantity, the supply voltage and the delivery location. Seven Star LLC will reply with availability and lead time; no price is shown on this page.