Brand:

Swagelok SS-18RS8 18 Series Needle Valve, 1/2 in. Tube, 1.8 Cv

Description

The Swagelok SS-18RS8 high-flow needle valve

Swagelok SS-18RS8 comes from the 18 series, the highest-capacity of the integral-bonnet needle valves in the O, 1 and 18 group. A 316 stainless body carries two 1/2 in. Swagelok tube fitting ends and a straight flow path with a 0.375 in. orifice. The maximum flow coefficient is 1.80, the stem is a regulating type with a stainless tip, and a bar handle in aluminum replaces the round phenolic knob of smaller valves.

The 1 series catalog gives orifice sizes between 0.080 and 0.375 in. and Cv values between 0.09 and 1.80 for the whole group. That means SS-18RS8 sits at the very top end of both ranges.

Why a bar handle

The handle pin and bar handle on 18 series valves are specified in anodized aluminum with a steel pin, according to the materials table. The longer lever helps an operator close a large-orifice valve against a 5000 psig line without a tool. It also gives a clearer visual indication of valve position from a distance. Bar handle valves in the catalog are also available for panel mounting.

Because the bar handle is anodized aluminum, avoid strong alkaline cleaners that strip anodizing, and watch for galvanic marks if the valve is mounted on carbon steel brackets in a marine atmosphere. The metal bar will also pick up heat from hot piping, so wear gloves when adjusting valves on steam-traced lines.

At 1.80 Cv, the valve can pass substantial flow when opened fully. On gas lines at 5000 psig, opening quickly can create a rapid pressure rise in downstream instruments, so open in small increments. For liquid service, check that the downstream device and hose can tolerate the maximum flow, otherwise use one of the smaller needle valves for tighter control.

When ordering spares for a maintenance store, record the full string SS-18RS8 on the bin label, and cross-reference it to the equipment tag so the correct handle type is issued during turnarounds.

Where the plant keeps several needle valve sizes, colour-coded tags help avoid mixing 1/2 in. and 1/4 in. valves during panel reassembly. The difference between SS-18RS8 and its smaller siblings is not only the end connection but also the larger body and handle, and fitting the wrong size into a tight panel is a frequent reason for rework.

A practical consideration for SS-18RS8 is orientation of the bar handle: in a closed panel, the bar sweeps a wide arc and can strike neighbouring tubing, so allow clearance equal to the bar length on both sides. Where space is tight, the smaller phenolic-knob valves of the same series can be a better layout choice, provided their lower Cv still meets the flow requirement.

Record the bar handle position at commissioning.

As a rule, schedule SS-18RS8 replacement together with its neighbouring needle valves during major turnarounds, since packing, knob and handle parts age at the same pace in the same environment, and a single shutdown window is cheaper than several small interventions across the year.

SS-18RS8 data table

Part number SS-18RS8
Series 18 series integral-bonnet
Body 316 stainless steel
Connections 1/2 in. Swagelok tube fitting x 2
Pattern Straight, 2-way
Stem Regulating, 316 stainless tip
Orifice 0.375 in.
Max Cv 1.80
Rating at 100 F 5000 psig (344 bar)
Rating at 450 F 3435 psig (236 bar)
Min / max temperature Minus 65 F / 450 F
Handle Aluminum bar
Cleaning SC-10
Low emissions Certified

SS-18RS8 compared with other Swagelok needle valves

On the same 1/2 in. tube, SS-1RS8 has a 0.250 in. orifice and 0.73 Cv and a phenolic knob, so SS-18RS8 offers about two and a half times the capacity. SS-1RF4 gives 0.73 Cv with female NPT ends. The 1/4 in. SS-1RS4 and SS-1VS4 give 0.37 Cv. Select SS-18RS8 whenever a half-inch line must flow more than about three-quarters of a Cv while still being throttled by a needle stem.

Applications

This valve fits large instrument supply headers, sampling loops with high sample rates, cooling-water bleed lines, bypass lines around control devices and test circuits at pump skids. Oil and gas operators in Oman use similar valves for flare-knock-out sampling taps and nitrogen purge manifolds.

Installation and packing

The 18 series uses the same live-loaded chevron packing as the rest of the group. Tighten the packing nut only enough to stop weeping. Mount rigidly, because the bar handle adds leverage and can load the tubing if the valve is not supported. Observe the catalog limits for packing materials if the line exceeds 250 degrees F.

Maintenance planning

Check bar handle set screw and pin during rounds. If the plant uses fugitive emission monitoring, include the valve in the leak detection route.

Ordering notes

Quote SS-18RS8 with quantity and specify panel mounting if needed. Related items in the family are SS-1RS8, SS-1VS4 and SS-1RF4.

Quick answers about SS-18RS8

What is the flow capacity of Swagelok SS-18RS8? Maximum Cv is 1.8 with a 0.375 in. orifice, the largest values in the O, 1 and 18 series group of needle valves.

What handle does SS-18RS8 use? An aluminum bar handle, which gives more leverage than the phenolic knob of the 1 series valves.

What is the pressure rating of SS-18RS8? 5000 psig at 100 degrees F (344 bar at 37 degrees C), derating to 3435 psig at 450 degrees F.

Is SS-18RS8 a regulating valve? Yes, the listed stem type is regulating with a 316 stainless steel stem tip.

What are the end connections of SS-18RS8? Both ends are 1/2 in. Swagelok tube fitting connections on a 316 stainless steel body.

Documents and quotation

The datasheet attached is the manufacturer catalog for integral-bonnet needle valves. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. Send the RFQ with SS-18RS8, the quantity and your delivery location.

Datasheets & Documents
  • PDF Datasheet Swagelok SS-18RS8 18 Series Needle Valve, 1/2 in. Tube, 1.8 Cv Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Swagelok is the American maker of tube fittings and small-bore valves, best known for its two-ferrule compression tube fitting. Fred A. Lennon and Cullen B. Crawford founded it in Cleveland, Ohio, in July 1947 as Crawford Fitting Company to make that fitting. Lennon bought the whole business and the patent in 1948, and the company has been based in Solon, Ohio, since the mid-1960s.

Seven Star LLC is an independent supplier in Muscat. We list Swagelok tube fittings, needle, ball, check, relief and metering valves, filters, regulators and sample cylinders, and supply them for instrument tubing and analyser systems in Oman and the GCC by exact part number.

Swagelok company profile

Established July 1947, Cleveland, Ohio, as Crawford Fitting Company
Founders Fred A. Lennon and Cullen B. Crawford; Lennon bought out Crawford in 1948
Headquarters Solon, Ohio, since the mid-1960s
Product families Tube fittings and adapters, face seal fittings, needle, ball, plug, check, relief and diaphragm valves, filters, regulators, quick-connects, sample cylinders and hoses

Milestones

  • 1947: Fred A. Lennon and Cullen B. Crawford found Crawford Fitting Company in Cleveland in July.
  • 1948: Lennon buys out Crawford.
  • Mid-1960s: Headquarters move to Solon, Ohio.

Swagelok products we list

Family Models Typical use
Tube fittings Overview, SS-810-6 union, SS-810-3 tee, SS-810-9 elbow, SS-810-4 cross, SS-810-1-8 male connector, SS-810-7-8 female connector, SS-810-61 bulkhead, SS-12M0-6 metric union, VCR face seal Leak-tight connections on instrument and process tubing
Needle and metering valves SS-1RS4, SS-1RF4, SS-18RF6, SS-6NBS6, SS-20VS4, SS-4MG Isolation and fine flow adjustment on instrument lines and sample systems
Ball and plug valves 40G, 40GX 3-way, 60 Series, 83 Series, P4T plug Quick quarter-turn shut-off and switching
Check, relief and sealed valves SS-4C-1, CH, R3A, RL3, SS-4BK bellows, SS-DLS4 diaphragm Backflow prevention, overpressure relief and leak-free sealing for toxic or high-purity media
Filters, regulators, sampling SS-4F-2, SS-4TF-7, KPR regulator, sample cylinders, QC quick-connects Analyser sample conditioning and gas or liquid sampling

A Swagelok part number can be read directly. In SS-810-6, "SS" is 316 stainless steel, "810" means a 1/2 in. tube fitting (8 sixteenths of an inch, 10 series), and "-6" is a union. A suffix such as "-8" adds a 1/2 in. NPT end, and "M0" marks metric tube, as in SS-12M0-6 for 12 mm. Tube fittings must be made up the same way every time: finger-tight, then 1 1/4 turns for most sizes. A gap inspection gauge confirms the fitting has been pulled up.

Where Swagelok products are used

In Oman and the GCC, Swagelok fittings and valves are used on instrument impulse lines, analyser sample systems, hydraulic and pneumatic control tubing, chemical injection and gas sampling in oil and gas, refining, petrochemical, power and laboratory installations.

Ordering Swagelok products: what we need

Send the full Swagelok part number (for example SS-810-6 or SS-1RS4), the material, and the tube size in inches or millimetres. For valves, add the end connections and any options. For sample cylinders, add the volume, pressure rating and end configuration.

Facts checked against Swagelok company history, October 2026.

FAQ

Questions about the Swagelok SS-18RS8 18 Series Needle Valve, 1/2 in.

Answers from our engineering team on installation, compatibility and integration.

01What is the flow capacity of Swagelok SS-18RS8?
Maximum Cv is 1.8 with a 0.375 in. orifice, the largest values in the O, 1 and 18 series group of needle valves.
02What handle does SS-18RS8 use?
An aluminum bar handle, which gives more leverage than the phenolic knob of the 1 series valves.
03What is the pressure rating of SS-18RS8?
5000 psig at 100 degrees F (344 bar at 37 degrees C), derating to 3435 psig at 450 degrees F.
04Is SS-18RS8 a regulating valve?
Yes, the listed stem type is regulating with a 316 stainless steel stem tip.
05What are the end connections of SS-18RS8?
Both ends are 1/2 in. Swagelok tube fitting connections on a 316 stainless steel body.