Brand:

Flowserve Limitorque SB-4 Spring-Compensated Actuator

Description

Flowserve Limitorque SB-4 spring-compensated Limitorque actuator overview

The SB-4 is the single-compensating spring variant of the Limitorque SMB multi-turn electric actuator, made by Flowserve. It takes the gearing, torque and limit switches and electrical options of the SMB-4 and adds a spring-loaded stem nut, so the stem nut can float in a controlled way instead of being rigidly fixed. The manufacturer rates the SB-4 at 8,300 ft-lb (11,253 Nm) of torque and 250,000 lb (1,112 kN) of thrust, the same figures as the matching standard size.

Two valve duties drive the choice of an SB actuator. In high-temperature service the valve stem grows with heat, and a rigid stem nut can jam the valve; the SB spring package allows for thermal expansion and contraction of the stem and stem nut. In high-speed closure, as on certain gate and globe valves, the spring assembly absorbs the seating shock, and the manufacturer says this lets SB actuators work at speeds up to three times the normal rate. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.

Key features of the SB-4

  • Spring-loaded stem nut that floats upward to absorb seating shock and expands to keep the valve firmly seated.
  • Allowance for thermal growth of the valve stem in high-temperature lines, which reduces the risk of a jammed valve.
  • Same torque and thrust ratings, gear ratios and electrical options as the equivalent SMB, so engineering carries over unchanged.
  • Same mounting base as the standard SMB-4, which allows an SB-4 to be exchanged for a comparable SMB if valve conditions change.
  • A double-compensating SBD version is offered for stem contraction and torque back-seating duties.

Flowserve Limitorque SB-4 technical specifications

Model Flowserve Limitorque SB-4 single-compensating actuator
Base size SMB-4
Maximum torque rating 8,300 ft-lb (11,253 Nm), commercial service
Maximum thrust rating 250,000 lb (1,112 kN)
Maximum stem capacity, SB 5.00 in
Maximum stem capacity, SBD 5.00 in
Available motors, 4-pole (ft-lb) 100, 150, 200, 250, 300
Available motors, 2-pole (ft-lb) 100, 150, 200, 250
Weight adder over SMB-4 for SB 470 lb (213 kg)
Weight adder over SMB-4 for SBD 960 lb (435 kg)
Mounting pilot 9.000 in (228.6 mm), length 0.375 in
Mounting holes 1 1/4-7 UNC x 2.00 in
Bolt circle 8 holes at 45 degrees on a 16.000 in (406.4 mm) bolt circle
Mounting base diameter 18.75 in (476.25 mm)
Ambient temperature rating -20 to 150 degrees F (-29 to 66 degrees C)
Gear case lubricant NLGI grade 0 grease

The table repeats the brochure data for the SB-4. The base weight of the equivalent SMB-4 is 2,115 lb (959 kg) with its largest motor, and the adder in the table is added to that for the spring package.

Where to use the SB-4 in Oman and the GCC

  • Steam isolation and bypass valves in power stations and heat recovery units, where thermal movement of the stem is large.
  • High-temperature gate and globe valves in refineries, petrochemical units and hydrocarbon processing plants.
  • Fast-closing gate or globe valves that seat on torque, where an unsprung nut would transmit the full seating shock into the gear train.
  • Cokers and other cyclic thermal services, which the manufacturer names among the heavy applications for the SMB family.
  • Replacement of an existing SMB-4 actuator in the field when a valve starts to show thermal binding.

Choosing between SB-4, SBD and a plain SMB-4

A plain SMB-4 is the right choice for most gate and globe valves. The SB-4 becomes worthwhile when the stem nut must move to follow thermal expansion, or when fast closing would otherwise hammer the seats. If the stem contracts as well as expands, or if the valve is torque back-seated, the SBD double-compensating version lets the nut float in both directions. The brochure gives the maximum stem capacity of the SB-4 as 5.00 in and the SBD as 5.00 in, so check the valve stem diameter against those numbers before ordering.

Torque and thrust requirements are chosen exactly as for the SMB. Motors in the ratings of 100, 150, 200, 250, 300 ft-lb for four-pole and 100, 150, 200, 250 ft-lb for two-pole are offered, and the same controls packages and position options apply.

Installing the SB-4

Installation of the SB-4 follows the SMB and SB installation manual. Confirm the order number and serial number on the nameplate, mount the actuator on the SMB-4 pattern with 1 1/4-7 UNC x 2.00 in on 8 holes at 45 degrees on a 16.000 in (406.4 mm) bolt circle, and make sure the stem nut and stem are clean and lubricated.

Set the torque switch and the geared limit switch as for the standard SMB-4, then operate the handwheel to confirm free movement before applying motor power. Confirm the direction of rotation at mid-travel.

Maintenance of the SB-4

Inspect the main gear case lubrication every 18 months or 500 cycles, whichever occurs first, the geared limit switch every 36 months or 1,000 cycles, and grease the drive sleeve top bearing every 6 months through its pressure fitting. A routine check at least every 18 months also covers moisture in the limit switch compartment, clean electrical contacts, tight terminals, sound gaskets and a motor megger test, where one megohm or higher is normal.

Ordering notes for the SB-4

When you request a quotation for the SB-4, state the valve type, stem diameter, operating temperature, closing speed, supply voltage and frequency, hazardous area class and the controls package. If you are replacing an existing actuator, send the nameplate order number and serial number. The SMB-4, SBD variants and neighbouring sizes are quoted separately.

SB-4 summary of answers

The SB-4 provides 8,300 ft-lb of torque and 250,000 lb of thrust, accepts a stem of up to 5.00 in, and adds 470 lb to the SMB-4. The questions below cover the spring package, the motors and how to order.

Documents and quotation

The manufacturer SMB brochure, which contains the SB and SBD ratings, is attached as the datasheet for the SB-4. The SMB and SB installation manual covers installation and lubrication. To request a quotation, send the part number SB-4 with the quantity and delivery location, and the team will reply with availability and lead time; this page shows no prices.

Other Models in the Limitorque SB Range

Seven Star LLC supplies models from the Limitorque SB range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Flowserve Limitorque SB-00 Spring-Compensated ActuatorElectric ActuatorsView details
Flowserve Limitorque SB-0 Spring-Compensated ActuatorElectric ActuatorsView details
Flowserve Limitorque SB-1 Spring-Compensated ActuatorElectric ActuatorsView details
Flowserve Limitorque SB-2 Spring-Compensated ActuatorElectric ActuatorsView details
Flowserve Limitorque SB-3 Spring-Compensated ActuatorElectric ActuatorsView details
Flowserve Limitorque SB-4 Spring-Compensated ActuatorElectric ActuatorsYou are viewing this model
Datasheets & Documents
  • PDF Datasheet Flowserve Limitorque SB-4 Spring-Compensated Actuator Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Flowserve is the American flow control company for pumps, valves, mechanical seals and valve automation, known through brands such as Durco, Worthington, Byron Jackson, Valtek, Limitorque, Worcester, Logix and Argus. It was formed on 22 July 1997 by the merger of equals of Durco International and BW/IP, whose heritage reaches back to Simpson & Thompson (1790) and Byron Jackson (1872). Flowserve Corporation is headquartered in Irving, Texas, and listed on the New York Stock Exchange.

Seven Star LLC sources and supplies Flowserve pumps, seals, control valves, ball valves, actuators and positioners for process plants in Oman, working from the nameplate data and the manufacturer's documentation.

Flowserve company profile

Formed 22 July 1997, merger of Durco International and BW/IP
Heritage companies Simpson & Thompson, later Worthington Simpson (1790); Byron Jackson (1872); Duriron foundry, later Durco (1912)
Headquarters Irving, Texas, USA
Ownership Flowserve Corporation, public company (NYSE: FLS)
Product families API and ANSI process pumps, Durco and Worcester ball and plug valves, Durco TX3 triple-offset and Valtek butterfly and globe control valves, Limitorque electric actuators, Logix positioners, mechanical seals

Milestones

  • 1790: Thomas Simpson founds Simpson & Thompson, a predecessor of Worthington Simpson pumps.
  • 1872: Byron Jackson is founded, a root of BW/IP.
  • 1912: The Duriron foundry, later Durco, is launched.
  • 1997: Durco International and BW/IP merge on 22 July to form Flowserve, listed on the NYSE as FLS.

Flowserve product families listed here

Flowserve pumps on this page are the Durco Mark 3 ANSI process pump and the ECPJ vertical sump pump built to API 610 type VS4. Sealing products are the ISC2 cartridge mechanical seal to API 682 and DuraClear barrier fluid for dual seal systems. Flowserve valves include the Valtek Mark One globe control valve, Argus floating and trunnion-mounted ball valves (EK71, FK79, FK76M) and Durco Microfinish ball valves. Automation is covered by Limitorque MX and L120 multi-turn electric actuators, the Rotadisk RD and RDF pneumatic actuator and the Logix 3800 digital positioner.

Where Flowserve equipment is used

Mark 3 pumps handle acids, caustic, solvents and utilities in chemical and petrochemical units. VS4 sump pumps drain pits and collection tanks. Valtek control valves and Argus ball valves are found in refining, gas processing, power and desalination, and Limitorque actuators operate gate and globe valves on pipelines, tank farms and water networks across the GCC.

Flowserve products we list

Family Examples
Ball Valves Argus EK71 End-Entry Floating Ball Valve, Argus FK76M Trunnion Mounted Ball Valve, Argus FK79 Floating Ball Valve, Durco Microfinish Ball Valves, Worcester Series 44 Three-Piece Ball Valve
Pumps DS-4614-5-F DuraClear Barrier Fluid, Durco Mark 3 ANSI Process Pump, ECPJ 25-200-R API 610 VS4 Vertical Sump Pump, ISC2 API 682 Cartridge Mechanical Seal
Control Valves Valtek Mark 100 Ultra-Capacity Globe Control, Valtek MaxFlo 4 Eccentric Rotary Plug Control, Valtek Valdisk High-Performance Butterfly, Valtek Mark One Globe Control Valve
Valve Actuators Limitorque L120 Multi-Turn Electric Actuator, Rotadisk RD and RDF Pneumatic Actuator, Limitorque MX Multi-Turn Actuator
Butterfly Valves Durco TX3 Triple Offset Butterfly Valve
Valve Positioners Logix 3800 Digital Positioner

Ordering Flowserve parts: what we need

The serial number on the nameplate is the key to Flowserve records for a pump, valve or actuator. Please add the following by product type:

  • Pumps: size and model, impeller diameter, materials, seal arrangement, and the part name and item number from the sectional drawing
  • Mechanical seals: seal type and size, drawing or part number, materials code, pumped fluid and flush plan
  • Valves: size, pressure class, body and trim materials, end connections, and the actuator and positioner model
  • Limitorque actuators: unit size, order and serial number, supply voltage, wiring diagram number

Facts checked against Flowserve's SEC filings and published company histories, October 2026.

FAQ

Questions about the Flowserve Limitorque SB-4 Spring-Compensated

Answers from our engineering team on installation, compatibility and integration.

01What is the difference between SB-4 and SMB-4?
The SB-4 adds a single-compensating spring package to the SMB-4, so the stem nut can float to absorb thermal growth or seating shock. Torque, thrust, gear ratios and electrical options stay the same as the SMB-4.
02What ratings does the SB-4 have?
The brochure lists 8,300 ft-lb (11,253 Nm) torque and 250,000 lb (1,112 kN) thrust for the SB-4, with a maximum stem capacity of 5.00 in for SB and 5.00 in for SBD.
03Does the SB-4 use the same mounting base as the SMB-4?
Yes, the brochure says SB and SBD actuators share the mounting base of the standard SMB, so the SB-4 can be interchanged with a comparable SMB-4 if valve conditions change.
04Which motors are available for the SB-4?
The brochure lists 4-pole motors of 100, 150, 200, 250, 300 ft-lb and 2-pole motors of 100, 150, 200, 250 ft-lb. The supply can be 230, 460 or 575 V at 60 Hz, or 380 or 415 V at 50 Hz.
05How do I request a quotation for the SB-4?
Send an RFQ with the part number SB-4, the quantity, the valve stem size and the delivery location. Seven Star LLC will reply with availability and lead time; no price is shown on this page.