- Automation & ControlView all 2,759 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: ifm
ifm SI1004 Flow Monitor, 4-20 mA Output (Archive Article)
Description
ifm SI1004 overview
The ifm SI1004 is an earlier-generation flow monitor with a 4 to 20 mA analogue output for liquids, listed in the manufacturer datasheet as an article that is no longer available. Its two-colour ten-LED display and M18 x 1.5 internal thread process connection are typical of the older SI series. The datasheet gives the ordering description SID10ADB100G/US-100-IAZ and names the SI5004 as an alternative article.
Status note: in the manufacturer datasheet the SI1004 is listed by the manufacturer as an article that is no longer available (archive entry), with the SI5004 named as the alternative article. The datasheet adds that when an alternative article is chosen, its technical data may differ, so engineers should compare the new data sheet before replacing an installed unit. This page describes the SI1004 as documented in that datasheet; ask us about current availability when you send the RFQ.
Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. We list this device so that maintenance, procurement and project teams can quote the exact part number against the manufacturer data.
Key features of the SI1004
- Analogue signal output of 4 to 20 mA with overload protection.
- Liquid setting range 3 to 60 cm/s as listed in the datasheet.
- Ten LEDs, two-colour, indicate the flow state on the head.
- Archive status per datasheet: the manufacturer lists the SI5004 as the alternative.
- Same 50 mm housing family as the SI5xxx range.
SI1004 technical specifications
| Parameter | Value from the manufacturer datasheet |
|---|---|
| Number of inputs and outputs | Number of analogue outputs: 1 |
| Process connection | threaded connection M18 x 1,5 internal thread |
| Media | Liquids |
| Medium temperature [°C] | -25…80 |
| Pressure rating | 300 bar 30 MPa |
| Operating voltage [V] | 20…36 DC; (according to EN 50178 SELV/PELV ; with reference to UL:) |
| Current consumption [mA] | 90; (without load) |
| Reverse polarity protection | yes |
| Power-on delay time [s] | 15; (optically indicated) |
| Total number of outputs | 1 |
| Output signal | analogue signal |
| Number of analogue outputs | 1 |
| Analogue current output [mA] | 4…20 |
| Max. load [Ω] | 500 |
| Overload protection | yes |
| Setting range [cm/s] | 3…60 |
| Response time [s] | 1…10 |
| Ambient temperature [°C] | -25…80 |
| Protection | IP 67 |
| Shock resistance | DIN IEC 68-2-27 50 g (11 ms) |
| Vibration resistance | DIN EN 60068-2-6 20 g (55…2000 Hz) |
| Dimensions [mm] | 60.5 x 42 x 109 |
| Materials | PBT-GF20 |
| Materials (wetted parts) | stainless steel (316L/1.4404); O-ring: FPM 8 x 1,5 gr 80° Shore A |
| Probe diameter [mm] | 8.2 |
| Installation length EL [mm] | 45 |
| Display | function 10 x LED, 2-colour |
All values above are taken from the manufacturer datasheet for the SI1004. Ranges are written with three dots, for example 18…30 means 18 to 30. Where a limit depends on the medium or the installation, the datasheet condition applies.
Typical applications in oil and gas, utilities, water and manufacturing
Typical uses in the region include protecting pumps and heat exchangers against dry running or loss of cooling water, proving circulation in lube-oil, seal-water and chilled-water loops, and detecting flow of liquids or gases in utility headers on process skids, compressor packages and water treatment plants.
In Oman and the wider GCC, flow monitoring devices like the SI1004 are found in pump protection, cooling-water proving and utility flow supervision. Hot ambient conditions, dust and long cable runs make a sensor with clear local indication and stable outputs valuable, because it shortens fault finding for the shift technician. Check the ambient and medium temperature limits in the table above against the actual site conditions before selecting the device.
Selection and compatibility notes for the SI1004
Because the SI1004 is an archive article, sourcing is mainly for like-for-like replacement of installed units. The manufacturer’s own note says that when selecting an alternative article, technical data may differ, so compare the liquid setting range (3 to 60 cm/s here, against 3 to 300 cm/s for the SI5004) and the electrical specification before changing the part.
When you match this device to an existing loop, compare the supply voltage, output type, connector and process connection with the installed device, and confirm that the control system input accepts the signal. Because the part number identifies one exact version in the family, a similar-looking sibling can differ in output polarity, range or thread, and it is better to quote the exact designation than a family name.
Installation and commissioning
The probe must sit in the flow with its sensing end fully immersed in the medium, in a straight pipe section away from valves, elbows and pumps, so that the flow profile is stable. Use the tightening torque shown on the datasheet drawing and a suitable process adapter. After installation, set the switch point or analogue range under real flow conditions rather than relying on factory settings, and note the setting in the maintenance log.
Before power-up, check the wiring against the connection diagram in the datasheet, and after power-up allow any start-up delay listed in the table to elapse before judging the output. Document the settings made on site together with the serial number so that a replacement can be configured identically.
Maintenance and service
Check the probe for deposits, scale or oil film at the intervals the process demands, because coating on a probe can shift the response. Verify the switch point during planned shutdowns, inspect the O-ring and the M12 connector for damage, and keep a spare cable on the shelf.
Related products and ordering notes
Related ifm devices already listed in the Seven Star catalogue can be found through the brand page. When you request this device, please state the quantity, the required delivery location and whether a datasheet copy is needed. If the application is critical, tell us the process medium, pressure and temperature so the engineer can check the data before the quotation is prepared.
Frequently asked questions
- What is the ifm SI1004? The ifm SI1004 is a flow monitor with a 4-20 mA analogue output, listed as an archive article. The ifm SI1004 is an earlier-generation flow monitor with a 4 to 20 mA analogue output for liquids, listed in the manufacturer datasheet as an article that is no longer available.
- What supply and protection rating does the SI1004 have? According to the manufacturer datasheet the SI1004 operates from 20…36 DC; (according to EN 50178 SELV/PELV ; with reference to UL: and has protection IP 67.
- Is the SI1004 still available from the manufacturer? The datasheet marks the SI1004 as no longer available (archive entry) and names the SI5004 as the alternative. Compare the data sheets before replacing it.
- Does Seven Star LLC supply the SI1004 in Oman? Yes, Seven Star LLC quotes the SI1004 for projects and maintenance in Oman and the GCC. Send the part number SI1004 and the quantity and we will respond with availability.
- How do I get a quotation for the SI1004? Use the RFQ form on this page with the part number SI1004, the quantity and your delivery location. We will reply with a quotation after checking availability.
Documents and quotation
The manufacturer datasheet is attached to this page where the file is available, and it is the reference for every value shown here. To order, send the RFQ with part number SI1004 and the quantity required, together with the delivery location and any application details. Our team will confirm availability and respond with a quotation.
Datasheets & Documents
- Datasheet ifm SI1004 Flow Monitor, 4-20 mA Output (Archive Article) Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
ifm is a German family-owned maker of sensors and automation products, founded in Essen in October 1969 by Robert Buck and Gerd Marhofer. Its first products were inductive proximity sensors sold under the efector name. ifm is still headquartered in Essen, and the founders' sons, Martin Buck and Michael Marhofer, have led it since 2001.
Seven Star LLC lists ifm position, distance and pressure sensors and supplies them by exact article number to plants and machine builders in Oman and the wider Gulf region.
ifm company profile
| Founded | 1969, Essen, Germany |
|---|---|
| Founders | Robert Buck and Gerd Marhofer |
| Headquarters | Essen, Germany |
| Ownership | Family-owned |
| Product families | Inductive and capacitive proximity sensors, PN pressure sensors, O1D laser distance sensors, flow and level sensors, IO-Link masters |
Milestones
- 1969: ifm is founded in Essen.
- 2001: The founders' sons take over management.
ifm sensors listed on this page
ifm identifies every device with a short article number, and that number is what we order against. Three are listed here:
- O1D100: laser distance sensor for position and distance measurement
- PN7093: pressure sensor with local display
- NG5021: inductive proximity sensor with NAMUR output
Other ifm inductive sensors, pressure sensors and connection cables can be quoted on request when you send the article number.
ifm products we list
Ordering ifm sensors: what we need
Send the six-character article number printed on the housing (two letters and four digits, or similar). If the label is worn, a photo plus the thread size, sensing range, output type and connector style is enough for us to check the part against ifm documentation. For NAMUR sensors, tell us which isolating amplifier is in the loop. Buyers in the GCC who need a successor for a discontinued article can send the old number and we will check the replacement the manufacturer names.
Facts checked against ifm's own 50-year chronicle (ifm.com), October 2026.
Browse ifm products by category: Sensors & Transmitters, Pressure Instrumentation.
FAQ
Questions about the ifm SI1004 Flow Monitor, 4-20 mA Output (Archive
Answers from our engineering team on installation, compatibility and integration.
01What is the ifm SI1004?
The ifm SI1004 is a flow monitor with a 4-20 mA analogue output, listed as an archive article. The ifm SI1004 is an earlier-generation flow monitor with a 4 to 20 mA analogue output for liquids, listed in the manufacturer datasheet as an article that is no longer available.
02What supply and protection rating does the SI1004 have?
According to the manufacturer datasheet the SI1004 operates from 20...36 DC; (according to EN 50178 SELV/PELV ; with reference to UL: and has protection IP 67.
03Is the SI1004 still available from the manufacturer?
The datasheet marks the SI1004 as no longer available (archive entry) and names the SI5004 as the alternative. Compare the data sheets before replacing it.
04Does Seven Star LLC supply the SI1004 in Oman?
Yes, Seven Star LLC quotes the SI1004 for projects and maintenance in Oman and the GCC. Send the part number SI1004 and the quantity and we will respond with availability.
05How do I get a quotation for the SI1004?
Use the RFQ form on this page with the part number SI1004, the quantity and your delivery location. We will reply with a quotation after checking availability.


















Reviews
There are no reviews yet.