- Automation & ControlView all 2,744 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Servo Drives
- Pneumatic Cylinders
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Rotork
Rotork IQM35 Modulating Multi-Turn Electric Actuator
Description
Rotork IQM35 overview
The Rotork IQM35 is the modulating-duty member of the IQ family: the same sealed, self-contained multi-turn actuator, but built for continuous positioning on control valves rather than just open and close travel. In Rotork’s IQM and IQML electrical data the Rotork IQM35 appears with a catalogued seating torque of up to 544 Nm (400 lbf.ft) on 3-phase supplies. Rotork now lists that electrical data document as legacy, which makes the IQM35 relevant to plants that maintain or replace older installations like for like.
Modulating duty is a different regime from isolating duty. Where an isolating IQ is rated for a short 15 minute duty, the IQM is rated for S4 operation at the specified modulating torque with a cyclic duration factor of 50 percent (class C under EN15714-2). To make that practical the IQM35 uses a solid state starter instead of contactors, and Rotork gives the thyristor arrangement as five pairs of 1600 volt devices switching all three phases.
This page is intended to help engineers and purchasers identify the IQM35 quickly, compare it with neighbouring sizes and prepare a clear enquiry. All figures come from Rotork’s own published electrical and specification documents, and where a value is not published we do not quote one.
Key features of the IQM35 actuator
- Solid state starter on the IQM35, built for frequent starts on regulating valves.
- Dynamic braking: after a stop command a DC pulse is fed into the motor to stop it quickly, reducing overrun and improving positioning accuracy, enabled in software.
- Standard protection against stall, phase rotation errors and lost phase in addition to thermostats and the torque switch.
- Modulating duty is rated at S4 with a 50 percent cyclic duration factor.
- Class H insulation is available where the standard class F motor does not suit the duty cycle.
- No lost-motion hammer-blow on modulating actuators, with starting torque of at least 80 percent of pull-out torque.
IQM35 technical specifications
| Parameter | Value |
|---|---|
| Manufacturer | Rotork |
| Model | IQM35 |
| Range | IQM modulating multi-turn electric actuator |
| Duty class | S4 modulating, cyclic duration factor 50 percent (EN15714-2 class C) |
| Starter | Solid state, five pairs of 1600 V thyristors, with dynamic braking |
| Motor | Low inertia squirrel cage induction motor, TENV, class F insulation (class H available) |
| Motor protection | Dual embedded thermostat (132 °C); stall, phase rotation and lost phase protection |
| Listed speeds (400 V, 50 Hz) | 18, 24, 36, 48 and 72 rpm |
| Maximum catalogued seating torque | 544 Nm (400 lbf.ft) |
| Suggested high speed fuse (rated current) | 20 A (Ferraz K330013 suggested) |
| Rated torque current at max torque row | 4.52 A (400 V, 50 Hz) |
| Starting / stall current at max torque row | 19 A |
| Data voltages | 380, 400, 415 V at 50 Hz and 460, 480 V at 60 Hz |
| Source of electrical data | PUB002-120 |
IQM35 electrical and performance data
The table lists each output speed published for the IQM35 under 3-phase modulating duty at 400 V and 50 Hz. Rotork compiles the values from averaged production test data, so use them for cable and protection sizing rather than as guaranteed unit values.
| Speed (rpm) | Poles | Rated torque (Nm) | Rated torque (lbf.ft) | Starting / stall current (A) | Rated torque current (A) | Average modulating current (A) | Average power (kW) | Efficiency (percent) |
|---|---|---|---|---|---|---|---|---|
| 18 | 4 | 544 | 400 | 19 | 4.52 | 2.77 | 1.28 | 90 |
| 24 | 4 | 544 | 400 | 19 | 5.89 | 3.18 | 1.58 | 91 |
| 36 | 4 | 408 | 300 | 19 | 5.89 | 3.8 | 1.99 | 89 |
| 48 | 4 | 313 | 230 | 14 | 5.46 | 3.59 | 1.93 | 88 |
| 72 | 4 | 218 | 160 | 14 | 5.42 | 5.18 | 2.64 | 80 |
Because modulating actuators have no hammer-blow, the starting torque of the IQM35 is high, at least 80 percent of pull-out torque, so the actuator can respond to small demand changes without a run-up phase.
Typical applications in Oman and the GCC
In oil and gas facilities in Oman, the IQM35 is specified on isolation and control valves in gathering stations, pipelines and tank farms, where an actuator with integral controls and a lockable local/stop/remote selector simplifies operations. Utilities and power plants use similar IQM actuators on cooling water, feedwater and fuel lines. Water and desalination operators across the GCC rely on them for intake, transfer and distribution valves, where the sealed enclosure copes with humidity and dust. In manufacturing and petrochemical sites the IQM35 appears on process utilities and skid packages. Because the actuators are described by Rotork as suitable for indoor and outdoor use, with ambient limits of minus 30 to plus 70 degrees Celsius in the IQ specification, they suit the hot coastal climate of Muscat, Sohar and Duqm.
Typical valve types include gate and globe valves for multi-turn actuators and ball, plug and butterfly valves for part-turn actuators, so confirm the valve stem or shaft details when you request the IQM35.
Selection and compatibility notes for the IQM35
For the IQM35, size supply cables using the starting or stall current in the data table so that the volt drop stays within 15 percent of nominal voltage at full starting conditions. Rotork strongly recommends high speed fuses at the distribution panel for solid state starters: for sizes 10, 12 and 20 the rated fuse current is 10 A, and for sizes 25 and 35 it is 20 A, with a 660 V rated voltage. Variable frequency converters are not recommended as a supply, and UPS supplies should be low in harmonic distortion with a true sine wave output.
A short guide to reading the Rotork electrical data helps when comparing builds. Rated torque in the IQM and IQML document is the catalogued seating torque at full load and represents a torque switch setting of 100 percent. The starting or stall figure is the current drawn when the output begins to move or when the motor is stalled; standard protection limits torque to around 150 percent of rated when torque switch bypass is enabled, and stall is limited to 5 seconds. Average modulating torque corresponds to about half of the rated seating torque, which Rotork treats as representative for modulating duty, and the table gives the current, power and efficiency at that point. Modulating duty differs from isolating duty because continuous positioning is a requirement, hence the S4 rating with a cyclic duration factor of 50 percent. The motor is a low inertia squirrel cage induction design in a totally enclosed non-ventilated housing, with class F insulation, class B temperature rise, two embedded thermostats set at 132 °C and bearings sealed for life. Rotork also reminds users that the data is averaged from production tests and that individual test certificates are available on request.
Match the IQM35 to the valve by the maximum valve torque including a safety margin, the stroke or number of turns, the mounting flange and the required operating time. Rotork’s sizing guidance says the actuator must guarantee valve closure at the specified differential pressure and temperature, with enough margin that the torque switch can still trip at maximum valve torque when the supply is 10 percent below nominal. Mention any hazardous-area, SIL or fieldbus requirement in your enquiry, because the certification of an actuator depends on the exact build.
Installation and commissioning
Mount the IQM35 on the control valve with the drive coupling machined to the stem nut or gearbox input. Confirm the supply is three-phase at one of the listed voltages and fit the high speed fuses recommended for the starter. During commissioning set the open and close limits, then tune the positioning dead band and the dynamic braking in software through the Rotork setting tool; braking is enabled in the actuator settings. A step test across the working stroke shows whether the overrun is acceptable for the loop.
Rotork supplies a commissioning kit with its actuators comprising an installation manual, wiring diagram and cover seals. Keep the terminal compartment dry during cabling, and torque the cover fasteners evenly after wiring so the IQM35 retains its enclosure rating.
Maintenance and spare parts for the IQM35
Rotork designs the gear case as an oil-filled enclosure suitable for operation at any angle, and the motor and internal electrical elements are sealed from the environment, so routine maintenance on the IQM35 is mainly visual and functional. Check the cable glands, cover seals and fasteners during shutdowns, exercise infrequently used valves, and review the datalogger or event records for torque trends that point to valve wear. Replace seals if covers were opened. For hard-to-find parts and replacement units please send the full nameplate details together with the model IQM35.
Rotork IQM35 vs Other Rotork Modulating Multi-Turn Electric Actuator Variants
The Rotork IQM35 is the choice when your application specifically needs IQM35. Ordering a neighbouring size or rating in this family is the most common cause of returns, so compare the figure on the existing unit or the design data sheet before you send an RFQ.
| Variant | Distinguishing detail |
|---|---|
| Rotork IQM25 Modulating Multi-Turn Electric Actuator | IQM25 |
| Rotork IQM35 Modulating Multi-Turn Electric Actuator (this page) | IQM35 |
FAQ summary
The most common questions we receive about the IQM35 concern its torque rating, available output speeds, supply voltage options, and how to specify a replacement. In short, the IQM35 is a Rotork modulating multi-turn electric valve actuator; the data on this page is taken from the Rotork documents listed below; and the exact build always depends on the voltage, speed and options that you confirm in your RFQ. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.
Documents and quotation
The datasheet for the IQM35 is the Rotork electrical data document PUB002-120, which you can download from this page when available. To obtain pricing and lead time, send the RFQ with the part number IQM35, the quantity, supply voltage and frequency, valve type and any special requirements, and our team will respond promptly. Please note that the product is described by its model designation and that final configuration is confirmed against the manufacturer’s data.
Other Models in the IQM Range
Seven Star LLC supplies models from the IQM range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Rotork IQM10 Modulating Multi-Turn Electric Actuator | Electric Actuators | View details |
| Rotork IQM12 Modulating Multi-Turn Electric Actuator | Electric Actuators | View details |
| Rotork IQM20 Modulating Multi-Turn Electric Actuator | Electric Actuators | View details |
| Rotork IQM25 Modulating Multi-Turn Electric Actuator | Electric Actuators | View details |
| Rotork IQM35 Modulating Multi-Turn Electric Actuator | Electric Actuators | You are viewing this model |
Datasheets & Documents
- Datasheet Rotork IQM35 Modulating Multi-Turn Electric Actuator Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Rotork is a British flow control company best known for electric valve actuators. Jeremy Fry founded Rotork Engineering Company in Bath in 1957, the year its first actuator, the 100A, went on sale, and the group is still headquartered in Bath and listed on the London Stock Exchange. Today Rotork makes electric, pneumatic, hydraulic and electro-hydraulic actuators, gearboxes, precision regulators and valve positioners.
Seven Star LLC is an independent supplier listing Rotork actuators, Rotork Fairchild regulators, YTC positioners and spare parts for buyers in Oman and the GCC. Replacement units are matched from the actuator nameplate and wiring diagram number.
Rotork company profile
| Origin | Founded by Jeremy Fry in 1957 in Bath, England; first product the 100A valve actuator |
|---|---|
| Headquarters | Brassmill Lane, Bath, United Kingdom |
| Ownership | Rotork plc, a public company listed on the London Stock Exchange |
| Acquired brands | Fairchild precision pneumatic controls (2011, Winston-Salem, USA), YTC valve positioners (Young Tech Co., Seoul, 2014), Mastergear gearboxes (2016) |
| Product families | Intelligent electric actuators, control valve actuators, electro-hydraulic and fluid power actuators, gearboxes, precision regulators, positioners and network control systems |
Milestones
- 1957: Jeremy Fry founds Rotork in Bath, England; the first product is the 100A valve actuator.
- 2011: Fairchild precision pneumatic controls (Winston-Salem, USA) is acquired.
- 2014: YTC valve positioners (Young Tech Co., Seoul) is acquired.
- 2016: Mastergear gearboxes is acquired.
Rotork actuators, regulators and positioners
| Series | Type | Typical use |
|---|---|---|
| IQ3 | Intelligent multi-turn electric actuator | Gate and globe valves, penstocks and sluice gates; non-intrusive setup with a Bluetooth setting tool, double-sealed enclosure, data logging |
| IQT3 | Intelligent part-turn electric actuator | Ball, butterfly and plug valves and dampers, with the same setup and diagnostics as IQ3 |
| CVA | Precision control valve electric actuator | Continuous modulating control of linear and part-turn control valves where instrument air is not available |
| CMA | Compact modulating electric actuator | Small control valves, chemical injection and metering pumps |
| Skilmatic SI3 | Self-contained electro-hydraulic actuator | Spring-return fail-safe and ESD duty with partial stroke testing, needing only an electrical supply |
| GP / GH | Scotch yoke pneumatic (GP) and hydraulic (GH) actuators | Large quarter-turn valves on pipelines and ESD service; spring-return or double-acting |
| CP | Compact pneumatic quarter-turn actuator | Smaller on-off ball and butterfly valves on plant air |
| Fairchild 10, 30, 55, 66, M11, 81 | Precision pressure regulators | Instrument air to positioners and actuators, test benches; Model 66 in stainless steel for corrosive and offshore sites |
| Fairchild 1000 | No-bleed precision regulator | Saves instrument air or gas where continuous bleed is not acceptable |
| Fairchild 10BP, 4000ABP | Back pressure regulators | Holding upstream pressure in process and test systems |
| YTC YT-1000, YT-3300 | Valve positioners | Electro-pneumatic (YT-1000) and smart HART (YT-3300) positioning of linear and rotary pneumatic actuators |
Where Rotork equipment is used
Rotork actuators are common on oil and gas pipelines and terminals, refineries and gas plants, water and wastewater networks, desalination plants and power stations. Electric IQ actuators handle isolation valves on long pipelines and water mains, often networked over Rotork Pakscan, Modbus or another fieldbus. Skilmatic and scotch yoke actuators cover emergency shutdown valves, and Fairchild regulators and YTC positioners sit on pneumatic control valves throughout process plants.
Ordering Rotork actuators and spare parts: what we need
Send photos of the actuator nameplate with the model, serial number and wiring diagram number; the wiring diagram is usually inside the terminal cover. Rotork can identify the original build, including options and control interface, from the serial number. For a new application add the valve type and size, required torque or thrust, operating time, mounting flange (ISO 5210 or ISO 5211), power supply, control signal or network protocol, fail-safe requirement and hazardous-area marking. For regulators and positioners send the full model code and the pressure or signal ranges.
Facts checked against Rotork plc company information and product data, October 2026.
Browse Rotork products by category: Valve Actuator, Regulators, Valve Positioner.
FAQ
Questions about the Rotork IQM35 Modulating Multi-Turn Electric Actuator
Answers from our engineering team on installation, compatibility and integration.
01What is the maximum rated torque of the Rotork IQM35?
In the Rotork electrical data for 3-phase modulating duty at 400 V and 50 Hz, the IQM35 is listed with a maximum rated torque of 544 Nm (400 lbf.ft) at its 18 rpm build, and a lowest listed torque of 218 Nm at the fastest speed shown.
02Which output speeds are listed for the IQM35?
The data table for 3-phase modulating duty at 400 V and 50 Hz lists 18, 24, 36, 48 and 72 rpm for the IQM35. Other speeds, supply voltages or options may exist, so confirm the exact build in your RFQ.
03What current does the IQM35 draw at rated torque?
For the 18 rpm build under 3-phase modulating duty at 400 V and 50 Hz, Rotork lists a rated torque current of 4.52 A and a starting or stall current of 19 A. Individual production test certificates are available from the manufacturer for exact unit values.
04Can the IQM35 be set up without opening the covers?
Rotork describes setting of torque levels, position limits and indication contacts for the IQ family over an infrared or Bluetooth wireless interface, without removing the actuator covers and, where needed, without mains power.
05How do I request a quotation for the IQM35?
Send the part number IQM35 with quantity, speed, supply voltage, valve details and any hazardous-area or network needs, and we will answer your RFQ. Seven Star LLC is an independent supplier and is not affiliated with Rotork.


















Reviews
There are no reviews yet.