- Automation & ControlView all 2,760 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Forbes Marshall
Forbes Marshall 8400SHNTW SMARTPoz Smart Positioner
Description
Forbes Marshall 8400SHNTW SMARTPoz overview
The Forbes Marshall 8400SHNTW is a member of the SMARTPoz 8400S family of smart valve positioners. According to the manufacturer, the 8400SHN series is a microprocessor based positioner that gives fast, sensitive and accurate positioning for single-acting linear pneumatic actuators. It compares the 4-20 mA set point with the real position of the actuator stem and removes the positioning error with an internal PID control action. The unit is a two-wire device, so the same loop that carries the set point also supplies its operating power.
The distinguishing feature of this series is contact-less position sensing. A magnet mounted on the shaft moves in front of a pair of Hall-effect sensors inside the control unit, so there is no mechanical feedback linkage to wear, no backlash and no friction in the measurement chain. The heart of the positioner is a small piezo based transducer that converts the electrical signal from the microcontroller into a proportional pneumatic signal for a pilot valve, which then feeds air to the actuator. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.
The manufacturer publishes a model de-codification table. The base is 8400S, followed by a sensor letter, a communication letter, a position transmitter letter and an enclosure letter. For the Forbes Marshall 8400SHNTW, H means Hall sensor, N means 4-20 mA communication, T means a position transmitter is fitted and W means a weatherproof enclosure. The datasheet gives this exact example: Model 8400SHNTW, smart positioner with Hall sensor, position transmitter and weatherproof enclosure. The alternative letters are N for no position transmitter and E for an Ex-proof enclosure, and the datasheet notes that an intrinsically safe version is available on request.
Key features of the 8400SHNTW positioner
- Precise position control with an internal PID action and a robust aluminium pressure die-cast housing.
- Contact-less Hall sensing with no wear on the feedback parts and no backlash.
- Automatic or manual calibration for the full stroke, with a basic programming front fascia that does not need a configurator.
- Custom alphanumeric LCD with a bar graph; Hall-effect switches can be operated from outside with a bar magnet, while tactile keys need the lid to be opened.
- Split-range operation for two valves, and use for air-to-open or air-to-close duty regardless of the actuator type.
- Linear, equal percentage, inverse equal percentage or freely adjustable valve characteristics, independent of the plug characteristic.
- Low air consumption, stated as less than 0.02 cubic metres per hour at 6 bar.
- NAMUR tubeless connection for MF-series actuators, which saves external tubing, and retro-fitting of existing positioners is possible.
8400SHNTW technical specifications
The values below are taken from the manufacturer datasheet for the 8400SHN series. The position transmitter figures apply because the T option is part of the 8400SHNTW code.
| Part number | 8400SHNTW |
|---|---|
| Brand | Forbes Marshall |
| Family | SMARTPoz 8400S, Hall sensor, non-contact type |
| Controller | Microprocessor based, non-contact |
| Control input (set point) | 4-20 mA, two-wire loop powered |
| Compliance voltage | 10 VDC minimum, 3.4 mA or more at 500 ohm |
| Actuator type | Single-acting linear pneumatic, MF series or U series |
| Stroke length | 16, 20, 30, 60 and 100 mm |
| Pneumatic supply | 1.5 to 6 bar |
| Air quality | Filtered to 5 micron, oil class 3 (less than 1 ppm), dried to ISO 8573-1 class 3, humidity class I |
| Air consumption | Less than 0.02 cubic metres per hour at 6 bar |
| Pneumatic connection | 1/4 inch NPT (F) |
| Position feedback (T option) | Passive 4-20 mA output |
| Feedback supply | 12 to 30 VDC maximum, RL = (Vs – 5 V) / 20 mA |
| Feedback accuracy | Plus or minus 0.5 percent of span |
| Temperature stability | 0.2 percent per 10 K of full scale |
| Operating temperature | -20 to +80 degrees C |
| Ingress protection | IP66 |
| Housing | Aluminium pressure die cast |
| Weight | 3 kg |
| Cable entries | Two M20 x 1.5 mm glands |
| Terminals | Screw type, for 1 square millimetre conductors, with an extra earth stud |
| Display | Custom alphanumeric LCD with bar graph |
| Standards | IEC 61000-2 and IEC 61000-4 EMC, IEC 60068-2-6 vibration, IEC 60068-2-29 bump |
Typical applications in Oman and the GCC
The manufacturer positions the SMARTPoz series for process plants such as power, pharma, chemical and paper. In the Gulf region the same single-acting linear control valve duties appear on steam and condensate headers in power and desalination plants, on utility steam in refineries and petrochemical sites, and on water and process lines in manufacturing. The weatherproof IP66 enclosure suits outdoor valve skids, while the stated operating range of minus 20 to plus 80 degrees C covers typical shade temperatures, although you should check surface heating on pipework in direct sun.
Because the Hall sensing system has no wear parts in the feedback path, the 8400SHNTW also appeals to maintenance teams who want to replace an older mechanical-feedback positioner without changing the valve. The datasheet confirms that retro-fitting of existing positioners is possible and that the unit works with linear or equal percentage characteristics regardless of the plug.
Selection and compatibility notes for 8400SHNTW
Before ordering, confirm that the actuator is a single-acting linear pneumatic type, because the datasheet names this as the supported actuator class. Check the stroke against the five stroke lengths listed, and confirm whether the actuator is an MF or U series unit so that the correct mounting arrangement and NAMUR tubeless option can be considered. Verify that the control system output can supply the required compliance voltage of 10 VDC at the loop current, since the datasheet states that this minimum must be maintained to keep the positioner switched on.
The T in 8400SHNTW means the position transmitter is present, so the loop for position feedback needs its own external supply of 12 to 30 VDC. If you need a unit without feedback, or an Ex-proof enclosure, those are different letters in the code and must be specified at the time of the request. The Ex data in the datasheet describes the explosion-protected variants, so do not assume the weatherproof version carries those approvals.
Installation and commissioning of 8400SHNTW
Mount the positioner on the four M8 threaded holes provided, 12 mm deep, and connect the 1/4 inch NPT (F) air ports. Supply filtered and dried air to the quality given in the table above. Run two-core cable of 1 square millimetre per conductor and 7 to 12 mm outside diameter through the M20 glands, tighten the glands for ingress protection and land the conductors on the screw terminals, using the earth stud as shown in the datasheet.
Commissioning uses the auto or manual full-stroke calibration described by the manufacturer. After calibration, select the valve characteristic, confirm air-to-open or air-to-close action, and for split-range service set the range for each valve. Check the position feedback current against the displayed position before handing the loop to operations.
Maintenance of the 8400SHNTW
The contact-less Hall principle removes the feedback linkage as a wear item. Routine care therefore centres on air quality: keep the supply filter and dryer serviced, because the low air consumption of the piezo and pilot arrangement relies on clean, dry air. Inspect the cable glands and the lid seal at each plant shutdown, and keep the enclosure free from heavy dust deposits. Record the calibration values so that a replacement unit can be set up quickly.
Related products and ordering notes
The 8400S family also includes variants with other sensor, communication and enclosure letters, and the manufacturer lists related SMARTPoz positioners on its product pages. When you send an enquiry for the 8400SHNTW, include the actuator make and model, stroke, supply pressure, the control system loop details and any special requirement such as an Ex-proof enclosure, so that the correct code can be confirmed.
8400SHNTW questions in brief
The 8400SHNTW is the Hall sensor, 4-20 mA, position transmitter, weatherproof version of the SMARTPoz 8400S. It is loop powered, handles single-acting linear pneumatic actuators with strokes from 16 to 100 mm, and has an IP66 aluminium housing weighing 3 kg.
Documents and quotation
The manufacturer datasheet for the 8400SHN series, including the model code table and dimensions, is attached to this page as a download. To request a quotation for the 8400SHNTW, send your RFQ to Seven Star LLC with the part number 8400SHNTW, the quantity required and the delivery destination, plus the actuator details listed above. No prices are shown on this page.
Datasheets & Documents
- Datasheet Forbes Marshall 8400SHNTW SMARTPoz Smart Positioner Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Forbes Marshall is the Indian steam engineering and control instrumentation group based in Pune. It traces its roots to a trading company set up in 1926 that supplied steam accessories to textile mills, and it began manufacturing in Pune in the late 1950s. Today it makes steam traps, boiler and steam system products, flowmeters and process analysers.
Seven Star LLC is an independent supplier in Muscat. We list Forbes Marshall steam, flow and water analysis products, and supply them with calibration consumables to plants in Oman and the GCC.
Forbes Marshall company profile
| Origins | Trading company J N Marshall & Co, 1926; Darius Forbes joined in 1946 |
|---|---|
| Manufacturing | First factory at Kasarwadi, Pune, in the late 1950s |
| Joint ventures | Krohne Marshall (1984, with KROHNE of Germany) for flow and level instruments, and ventures with ARCA Regler (control valves), CODEL (stack emission monitoring) and Vyncke (biomass boilers) |
| Product families | Steam traps and steam system equipment, boilers, flowmeters, control valves, water and steam analysers |
Milestones
- 1926: The trading company J N Marshall & Co is set up.
- 1946: Darius Forbes joins the business.
- Late 1950s: The first factory opens at Kasarwadi, Pune.
- 1984: Krohne Marshall is formed with KROHNE of Germany for flow and level instruments.
Forbes Marshall products we list
| Product | Type | Typical use |
|---|---|---|
| FMTD64 | Thermodynamic steam trap | Draining steam mains and tracing lines |
| FLOWIRL 8400 | Vortex flowmeter | Steam, gas and liquid flow measurement |
| FM TOC101 | Online TOC analyser | Organic contamination in condensate return and treated water |
| AMI Silica | Silica analyser | Silica monitoring in boiler feedwater, steam and demineralised water |
| Conductivity standards, pH buffer solutions | Calibration consumables | Routine calibration of conductivity and pH analysers |
A thermodynamic trap like the FMTD64 uses the flash steam above a disc to close and the condensate pressure below it to open. That makes it compact and tolerant of water hammer and superheat, which is why it is common on steam mains. On the water side, silica and TOC analysers protect boilers and turbines, because silica carries over with steam and deposits on turbine blades, and organics in returned condensate break down into acids.
Where Forbes Marshall products are used
In Oman and the GCC, these products are used in boiler houses, power and desalination plants, refineries, petrochemical and fertiliser plants, food and beverage plants and water treatment plants.
Ordering Forbes Marshall products: what we need
For steam traps and flowmeters, send the model, size, end connection, pressure rating, medium, and the operating pressure and temperature. For analysers, send the measuring range, the sample conditions and the number of channels. For consumables, send the value (for example pH 4, 7, 10 or the conductivity value) and the quantity.
Facts checked against Forbes Marshall company history, October 2026.
Browse Forbes Marshall products by category: Liquid Analytical Systems, Liquid Analytical Accessories.
FAQ
Questions about the Forbes Marshall 8400SHNTW SMARTPoz Smart Positioner
Answers from our engineering team on installation, compatibility and integration.
01What does the model code 8400SHNTW mean?
The manufacturer decodes it as the 8400S platform with a Hall sensor (H), 4-20 mA communication (N), a position transmitter (T) and a weatherproof enclosure (W).
02What control signal and power does the 8400SHNTW need?
It is a two-wire device powered from the 4-20 mA set point loop. The datasheet asks for a compliance voltage of at least 10 VDC, with 3.4 mA or more at 500 ohm, to keep it running.
03Which actuators can the 8400SHNTW be fitted to?
The datasheet states single-acting linear pneumatic actuators, naming the MF series and the U series, with stroke lengths of 16, 20, 30, 60 and 100 mm.
04Is the 8400SHNTW rated for hazardous areas?
The W in the code stands for weatherproof. The datasheet lists Ex-proof and intrinsically safe variants separately, so confirm the exact variant on your order before using it in a hazardous zone.
05How do I request a quotation for the 8400SHNTW?
Send an RFQ to Seven Star LLC with the part number 8400SHNTW, the quantity, the actuator type and stroke, and the delivery location in Oman or the GCC.


















Reviews
There are no reviews yet.