- Automation & ControlView all 2,776 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- Pneumatic Cylinders
- HMI Displays
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: SMC
SMC CDQ2B32-30D Compact Cylinder, 32 mm Bore, 30 mm Stroke
Description
SMC CDQ2B32-30D compact cylinder overview
The SMC CDQ2B32-30D is a double acting, single rod compact cylinder from the CQ2 family with a 32 mm bore and a 30 mm stroke, supplied with through-hole (standard) mounting. It is with a built-in magnet in the piston, so that solid state or reed auto switches can be added later without changing the cylinder. The compact body is only as long as the stroke plus a short fixed section, which is why this style is popular for clamps, pushers, small presses and positioning units where space is tight.
The model code reads: CDQ2 is the series, B selects through-hole (standard) mounting, 32 is the bore in millimetres, 30 is the stroke in millimetres, and D means double acting. The port thread type and the body option are left blank, which gives the standard rod end female thread and the standard port thread for this bore (Rc 1/8).
This page summarises the manufacturer catalog data for the SMC CDQ2B32-30D for buyers in Oman and the GCC. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.
Key features of the CDQ2B32-30D
The CQ2 compact cylinder is a standard-type, double acting, single rod cylinder available from 12 mm to 100 mm bore. The points that matter for the CDQ2B32-30D are as follows.
- Bore 32 mm with theoretical thrust of about 402 N on the extend stroke at 0.5 MPa, found by multiplying the piston area of 804 mm2 by the pressure.
- Allowable kinetic energy of 0.15 J for the standard version, which sets the limit for the load mass and speed at stroke end.
- Non-lube operation: the catalog states that lubrication is not required.
- Mounting: the CDQ2B32-30D has four through holes in the body that allow the cylinder to be bolted straight to a machine face.
- Piston speed range of 50 to 500 mm/s, with low speed and other special versions available through made to order codes.
- Rod end female thread as standard, with male thread, rubber bumper and boss in head side listed as body option choices in the family.
Mounting brackets, if you select the foot, flange or double clevis styles, are shipped together with the cylinder but not assembled, and cylinder mounting bolts are not included. Order the bolts separately if you need them.
CDQ2B32-30D technical specifications
The table lists the pneumatic specification of the CDQ2B32-30D from the manufacturer catalog. Values apply to the standard version. Special versions such as heat-resistant, cold-resistant, low-speed or heavy-duty scraper types are made to order and change some of these figures.
| Parameter | Value |
|---|---|
| Model | CDQ2B32-30D |
| Series | CDQ2 (CQ2 with built-in magnet) |
| Action | Double acting, single rod |
| Bore size | 32 mm |
| Stroke | 30 mm |
| Mounting style | Through-hole (standard) mounting |
| Fluid | Air |
| Proof pressure | 1.5 MPa |
| Maximum operating pressure | 1.0 MPa |
| Minimum operating pressure | 0.05 MPa |
| Ambient and fluid temperature | minus 10 to 60 degC when an auto switch is fitted |
| Lubrication | Not required (non-lube) |
| Piston speed | 50 to 500 mm/s |
| Allowable kinetic energy, standard | 0.15 J |
| Stroke length tolerance | plus 1.0 / minus 0 mm (before bumper change) |
| Port thread, standard | Rc 1/8 |
| Piston area, extend side | 804 mm2 |
| Theoretical thrust at 0.5 MPa, extend | about 402 N |
| Rod end | Female thread (standard) |
| Foot bracket part number (separate) | CQ-L032 |
For a 32 mm bore the catalog lists standard strokes of 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75 and 100 mm. A stroke of 30 mm is therefore a standard stroke for the CDQ2B32-30D, and intermediate strokes can be made to order.
Typical applications in Oman and the GCC
Compact cylinders such as the CDQ2B32-30D are used on production machinery in packaging, food processing, plastics and metal fabrication workshops across Oman and the Gulf. Typical jobs include clamping a part while it is machined or tested, pushing a product from a conveyor to a diverter, lifting a small stopper and pressing labels or seals.
In oil and gas and utility installations, the same cylinder type can be found inside skid frames and control cabinets, operating sample valves, small dampers and door latches. In water treatment and desalination plants it is used to actuate small gates and manual-to-automatic conversion mechanisms on filtration and dosing equipment.
The CDQ2B32-30D works in an ambient and fluid temperature of minus 10 to 60 degC when an auto switch is fitted, so shading and a clean, dry air supply are needed in outdoor and high-ambient environments. Dust on the rod should be controlled with a wiper or a boot, and heavy-duty scraper options exist for dusty sites.
Selection and compatibility notes for the CDQ2B32-30D
Start from the load and the pressure. At 0.5 MPa the extend thrust of the CDQ2B32-30D is about 402 N before friction and load factors are applied, so choose a bore that leaves a safety margin. For a horizontal load a load rate of 50 percent or lower is a common starting point for speed estimates.
Check the stroke-end energy. The standard version tolerates 0.15 J, so heavy loads or high speeds need a cushioning device, a speed controller or a larger bore. The catalog lists a rubber bumper version with a higher allowable kinetic energy for those applications.
Confirm the port thread. The CDQ2B32-30D uses Rc 1/8 ports in the standard configuration, and other thread types and one-touch fittings are available as separate codes in the family.
- Air quality: filtered and preferably dried air, no lubrication needed.
- Auto switches: built-in magnet allows D-A9 and M9 type switches to be added.
- Side loads: the cylinder is not a guide, so use a guide or a floating joint if the load is off-centre.
- Intermediate strokes: spacer type or dedicated body types are available on request.
Installation and commissioning of the CDQ2B32-30D
Mount the CDQ2B32-30D so that the load is aligned with the rod axis. The catalog warns that CQ2 compact cylinders are designed to save space, so they should not be used like tie-rod cylinders and a lateral load on the rod must stay inside the allowable limits. Use a floating joint or a guide if alignment cannot be guaranteed.
Connect the two ports to a 5-port valve or two 3-port valves through speed controllers. Raise the pressure slowly, check that the CDQ2B32-30D extends and retracts smoothly at the lowest speed that your process allows, then adjust the speed controllers to the working speed. Keep the piston speed in the 50 to 500 mm/s range given in the catalog.
When fitting or removing the retaining ring, use the correct pliers for a type C retaining ring and take care, because the ring can spring out and cause injury.
Maintenance and service life
The CDQ2B32-30D is a non-lube design, so regular lubrication is not required. Keep the air clean and dry, and drain filters often in humid locations. Check the rod surface and the wiper area for scratches, and inspect the fixing bolts and the rod end connection at every maintenance stop.
If air leaks from the rod cover or the cylinder slows over time, replace the cylinder or order the matching seal kit, which the catalog lists per bore size with codes such as CQ2B32-PS. Do not run the cylinder against a stroke end at high speed without a bumper or an external stopper.
Keep a spare CDQ2B32-30D or the same bore and stroke for critical lines to reduce downtime.
Related products and ordering notes
Related items for the CDQ2B32-30D include foot, flange and double clevis brackets (part numbers CQ-L, CQ-F and CQ-D followed by the bore code), auto switches such as the D-M9 and D-A9 types for the built-in magnet version, speed controllers, one-touch fittings and rod end accessories such as floating joints.
In your RFQ please state the quantity of the CDQ2B32-30D, the bore and stroke, the port thread type, and whether auto switches or any made to order feature are needed. If you are replacing a cylinder in service, send the nameplate or a photograph of it so that the code can be matched exactly.
Frequently asked questions about the CDQ2B32-30D
The questions below cover what customers most often ask about the CDQ2B32-30D: what the code means, which strokes are standard, how much force the cylinder gives and how to order it.
Documents and quotation
A datasheet extract with the how-to-order page, the specification table and the type and mounting bracket page of the CQ2 family is attached to this page. To request a quotation, send the RFQ with the part number CDQ2B32-30D, the quantity and the delivery destination, and we will confirm availability and lead time for Oman and the GCC.
Other Models in the CQ2 Range
Seven Star LLC supplies models from the CQ2 range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| SMC CQ2B25-30D Compact Cylinder, 25 mm Bore, 30 mm Stroke | Pneumatic Cylinders | View details |
| SMC CQ2B32-30D Compact Cylinder, 32 mm Bore, 30 mm Stroke | Pneumatic Cylinders | View details |
| SMC CQ2B40-30D Compact Cylinder, 40 mm Bore, 30 mm Stroke | Pneumatic Cylinders | View details |
| SMC CQ2B50-30D Compact Cylinder, 50 mm Bore, 30 mm Stroke | Pneumatic Cylinders | View details |
| SMC CQ2B63-30D Compact Cylinder, 63 mm Bore, 30 mm Stroke | Pneumatic Cylinders | View details |
| SMC CDQ2B32-30D Compact Cylinder, 32 mm Bore, 30 mm Stroke | Pneumatic Cylinders | You are viewing this model |
Datasheets & Documents
- Datasheet SMC CDQ2B32-30D Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
SMC is the Japanese specialist in pneumatic automation: air preparation units, solenoid valves, cylinders, fittings, process valves and sensors. Yoshiyuki Takada founded the company in Tokyo on 27 April 1959 as Shoketsu Kinzoku Kogyo, which means Sintered Metal Corporation, and its first products were sintered metal filters. SMC Corporation is headquartered in Tokyo and listed on the Tokyo Stock Exchange, and its products are used on machines and instrument air lines across the world.
Seven Star LLC, an independent supplier in Oman, lists SMC AW series filter regulators (AW20 and AW40) and the VX2 series direct-operated 2-port solenoid valve, and sources other SMC parts by full part number.
SMC company profile
| Founded | 27 April 1959, Tokyo, Japan, as Shoketsu Kinzoku Kogyo (Sintered Metal Corporation) |
|---|---|
| Founder | Yoshiyuki Takada (1928–2024) |
| First products | Sintered metal filters; pneumatic air line equipment from 1961 |
| Headquarters | Tokyo, Japan |
| Ownership | SMC Corporation, a public company listed on the Tokyo Stock Exchange |
| Product families | AF/AR/AW modular air preparation, VT/VQ/SY solenoid valves, VX/VXZ 2-port valves, air cylinders and rotary actuators, fittings and tubing, pressure and flow switches, vacuum equipment |
Milestones
- 1959: Shoketsu Kinzoku Kogyo is founded in Tokyo on 27 April and starts making sintered metal filters.
- 1961: Pneumatic air line equipment is added.
- 1964: Automatic control equipment becomes part of the business.
- 1967: The first overseas operation starts, with a stake in an Australian company.
- 1970: SMC begins making air cylinders.
SMC series listed on this page
The AW is a combined filter and pressure regulator in SMC's modular air preparation line. The body size is in the name: AW20 is the smaller unit and AW40 the larger, and the digits after the dash give the port size. A part number such as AW40-04-A therefore describes body size, port and options in one string. The VX2 is a direct-operated two-port solenoid valve for shutting off air, water, oil or steam, depending on the body and seal materials chosen.
SMC products we list
Ordering SMC parts: what we need
Give the complete SMC part number from the label, including thread prefix, options and the final suffix letter. For AW units state gauge, drain type and bracket if you need them. For VX2 valves send coil voltage, port size, orifice, body and seal material, and the fluid. Buyers in the GCC often have NPT or G threads on site, so say which thread standard the piping uses.
Facts checked against SMC's published corporate history, October 2026.
Browse SMC products by category: Regulators, Solenoid Valve.
FAQ
Questions about the SMC CDQ2B32-30D Compact Cylinder, 32 mm Bore, 30 mm
Answers from our engineering team on installation, compatibility and integration.
01What does the code CDQ2B32-30D mean?
CDQ2 is the series, B is through-hole (standard) mounting, 32 is the bore in millimetres, 30 is the stroke in millimetres and D means double acting. Blank option positions give the standard thread and rod end.
02Is 30 mm a standard stroke for the CDQ2B32-30D?
Yes. For a 32 mm bore the catalog lists standard strokes of 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75 and 100 mm, so 30 mm is a standard stroke.
03How much force does the CDQ2B32-30D produce?
Theoretical thrust on the extend stroke is about 402 N at 0.5 MPa, from a piston area of 804 mm2. Real output is lower after friction, so size the cylinder with a margin.
04What operating pressure and temperature apply to the CDQ2B32-30D?
Maximum operating pressure is 1.0 MPa, minimum is 0.05 MPa and proof pressure is 1.5 MPa. The temperature range is minus 10 to 60 degC when an auto switch is fitted, without freezing.
05How can I request a quotation for the CDQ2B32-30D?
Send an RFQ with the part number CDQ2B32-30D, the quantity and the delivery location. Seven Star LLC will reply with availability and lead time; this page shows no price.


















Reviews
There are no reviews yet.