Spirax Sarco CS10 Stainless Steel Clean Steam Separator

Overview

The Spirax Sarco CS10 Stainless Steel Clean Steam Separator is a precision moisture-removal device engineered to strip entrained water droplets from clean and pure steam lines before they reach critical process points. Complying fully with the ASME BPE (Bio-Processing Equipment) 2005 edition guide, the Spirax Sarco CS10 is purpose-built for facilities where steam dryness is not optional – pharmaceutical sterilizers, autoclaves, clean-in-place (CIP) systems, and food-grade process lines where wet steam compromises sterilization validation and damages sensitive control valves and instrumentation.

As the official authorized partner and exclusive regional representative for Spirax Sarco, Seven Star LLC proudly supplies the Spirax Sarco CS10 clean steam separator to industrial, pharmaceutical, and healthcare facilities across the Sultanate of Oman and the wider GCC. Engineers in Muscat, Sohar, and Salalah rely on Seven Star LLC for genuine Spirax Sarco hardware, complete technical documentation, and responsive local support – eliminating the long lead times and warranty uncertainty that come with grey-market imports.

Operating Principle of the Spirax Sarco CS10

The Spirax Sarco CS10 uses a centrifugal separation mechanism to remove moisture from a clean steam flow. As wet steam enters the separator body, its flow path is forced into a rotational pattern by an internal baffle arrangement. Because water droplets are significantly denser than steam vapor, centrifugal force flings the entrained moisture outward against the separator wall, where it coalesces and drains away through a connected steam trap or condensate drain point, while dry, saturated steam continues downstream through the outlet.

This separation happens with no moving parts and negligible pressure drop, meaning the Spirax Sarco CS10 introduces essentially zero disruption to line dynamics while delivering a measurable increase in steam dryness fraction. Because the wetted internals are entirely stainless steel with no elastomers or seals in the flow path, there is no risk of particulate shedding or chemical leaching into the clean steam stream – a critical requirement for sterile utility systems feeding autoclaves, SIP (Sterilize-in-Place) skids, and pure steam generators.

Engineering Design of the Spirax Sarco CS10

Built to ASME BPE 2005 standards, the Spirax Sarco CS10 separator body is manufactured from 316L stainless steel, with all product-contact surfaces finished to the low-roughness (Ra) requirements demanded by biopharmaceutical and food-grade hygienic piping. The exterior is polished to a bright, cleanable finish suited to washdown environments and cleanroom-adjacent installations, while the internal geometry is engineered to minimize dead-legs and crevices where bacteria or residue could accumulate.

Connection options are designed for direct integration into hygienic tube runs, with sizes and end-connection styles selected to match the ASME BPE tube schedule used throughout a typical clean steam distribution system. The separator is installed horizontally or vertically in-line, immediately upstream of the point of use or upstream of a clean steam pressure reducing station, with a condensate outlet piped to an appropriate steam trap set for continuous moisture discharge. Full technical and installation documentation (reference TI-P023-59 and IM-P023-60) is available to specify and commission the unit correctly.

Key Features

The Spirax Sarco CS10 clean steam separator combines hygienic construction with proven centrifugal separation performance:

• Manufactured entirely from stainless steel in full compliance with the ASME BPE 2005 edition guide for bio-processing equipment.
• Removes entrained moisture from clean and pure steam to protect sterilization validation and process integrity.
• Centrifugal separation design contains no moving parts, minimizing maintenance and eliminating wear-related failure modes.
• Negligible pressure drop across the separator preserves upstream steam pressure and system efficiency.
• Polished external finish and low-Ra internal surfaces suit cleanroom-adjacent and washdown installation environments.
• Protects downstream control valves, regulators, and instrumentation from erosion and water hammer caused by wet steam.
• Supports both horizontal and vertical in-line installation to fit existing hygienic pipe routing.
• Backed by complete Spirax Sarco technical and installation documentation for accurate specification and commissioning.

Industrial Applications

The Spirax Sarco CS10 is specified wherever clean or pure steam quality is a regulatory or process-critical requirement. Pharmaceutical manufacturers use it upstream of autoclaves and SIP skids to guarantee the dryness fraction needed for validated sterilization cycles, while food and beverage producers install it ahead of CIP and direct steam injection systems to prevent condensate carryover from affecting product quality. Hospitals and healthcare facilities rely on the same principle to protect sterile processing departments, and semiconductor and electronics manufacturers use clean steam separation to maintain the humidity and purity standards required in cleanroom environments.

As the officially authorized partner for Spirax Sarco, Seven Star LLC distributes the CS10 separator to pharmaceutical plants, hospital sterile services departments, food processing facilities, and district cooling and utility operators throughout Oman and the GCC, including the industrial zones of Sohar and Salalah and the greater Muscat industrial belt. Local stockholding and factory-trained technical support mean specifying engineers and procurement teams can secure genuine Spirax Sarco equipment with full traceability and warranty backing, rather than relying on unauthorized resellers.

Technical Specifications

Key technical parameters for the Spirax Sarco CS10 clean steam separator are summarized below; refer to datasheet TI-P023-59 for full sizing and pressure/temperature ratings.

Request a Quote for Spirax Sarco CS10 Stainless Steel Clean Steam Separator

Specify the Spirax Sarco CS10 Stainless Steel Clean Steam Separator with confidence by requesting a formal RFQ from Seven Star LLC. As the authorized partner for Spirax Sarco in Oman and the GCC, Seven Star LLC maintains regional warehouse stock, provides full technical datasheets on request, and connects your project directly with our instrumentation and steam systems division for sizing support, commissioning guidance, and after-sales service. Contact Seven Star LLC today to secure genuine Spirax Sarco clean steam equipment for your pharmaceutical, food-grade, or hospital sterile services project in Muscat, Sohar, Salalah, or anywhere across the GCC.

Related Products

• Spirax Sarco STS17.2 Steam-Trapping Station
• Spirax Sarco STERI-TROL Clean Service Control Valve
• Yarway Series 751/761 Repairable Drip and Tracer Steam Trap
• Spirax Sarco BTM7 Stainless Steel Thermostatic Clean Steam Trap
• Spirax Sarco SRV66 Sanitary Pressure Reducing Valve
• Spirax Sarco BT6-B Balanced Pressure Thermostatic Steam Trap