- Automation & ControlView all 2,760 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- HMI Displays
- Pneumatic Cylinders
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: Hoke
Hoke 1711F4Y Globe Needle Valve, 316 SS
Description
Hoke 1711F4Y needle valve overview
The Hoke 1711F4Y is a 316 stainless steel globe pattern needle valve from the 1700 series of forged body, integral bonnet valves. It has 1/4 inch female NPT inlet and 1/4 inch female NPT outlet connections, an orifice of 0.187 inch (4.7 mm), a flow coefficient Cv of 0.45, and a metal stem tip for service up to 450 degrees F. The manufacturer lists the 1700 series for cylinder valves, panel board instrumentation, pressure gauge valves, sampling systems, research laboratories, oxygen service and corrosive or high pressure service. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.
Needle valves are used where a small flow has to be started, stopped or set accurately, and the Hoke 1711F4Y suits that duty in 316 stainless steel. Buyers who search for the exact number 1711F4Y are usually replacing an installed valve, matching an existing bill of materials or ordering spares for a skid, so the full part number matters more than the series name alone.
Key features of the 1711F4Y
- Lock nut secures the packing nut and prevents accidental removal.
- Dyna-Pak packing sits below the stem threads, so the process fluid does not reach the stem threads.
- Every valve is tested for bubble-tight leakage at both the seat and the packing.
- Panel mounting is standard on all models, with a special high tolerance NPT thread.
- 1711F4Y in 316 stainless steel with 1/4 inch female NPT at the inlet and 1/4 inch female NPT at the outlet.
Dyna-Pak is the manufacturer packing system made of alternating TFE and metal wafers. As the packing nut is tightened the metal spacers squeeze the TFE against the stem, so the forces are concentrated at the stem and stem leakage is kept very low while cold flow of the TFE is limited.
1711F4Y technical specifications
The values in this table are taken from the manufacturer needle valve catalogue. Flow figures depend on the end connections, so confirm them against the order table for the exact part number.
| Part number | 1711F4Y |
|---|---|
| Brand | Hoke |
| Series | 1700 series, forged body, integral bonnet needle valve |
| Pattern | Globe |
| Inlet connection | 1/4 inch female NPT |
| Outlet connection | 1/4 inch female NPT |
| Body material | 316 stainless steel |
| Stem tip | Metal stem tip (17-4PH stainless steel stem tip) |
| Stem packing | TFE and 316 stainless steel wafers (Dyna-Pak) |
| Orifice | 0.187 inch (4.7 mm) |
| Flow coefficient Cv | 0.45 |
| Maximum operating pressure | 6000 psig (414 bar) at 70 degrees F (21 degrees C) |
| Operating temperature | minus 65 to plus 450 degrees F (minus 54 to plus 232 degrees C) |
| Stem | 316 stainless steel |
| Handle | Aluminium (1711 series) |
| Packing nut | XM-28 stainless steel |
| Lock nut | 316 stainless steel |
| Panel mounting nut | 316 stainless steel |
| Panel mounting | Panel hole 57/64 inch (22.6 mm) diameter, panel thickness up to 1/4 inch (6.4 mm) |
| Testing | Each valve is tested for bubble-tight leakage at the seat and at the packing |
The 1711F4Y is rated for 6000 psig (414 bar) at 70 degrees F (21 degrees C). The operating temperature range is minus 65 to plus 450 degrees F (minus 54 to plus 232 degrees C). As with all needle valves, the allowable pressure falls as temperature rises, so always read the pressure and temperature curve of the 1700 series in the catalogue before you finalise the selection.
Typical applications in Oman and the GCC
The manufacturer lists these uses for the 1700 series: cylinder valves, panel board instrumentation, pressure gauge valves, sampling systems, research laboratories, oxygen service and corrosive or high pressure service. In Oman and across the GCC these map naturally to sample conditioning panels and analyzer shelters at gas processing and refining sites, instrument air and utility headers at power and desalination plants, laboratory and test stand work, and general instrumentation in water treatment and manufacturing. The globe pattern valve 1711F4Y can be mounted through a panel wall.
- Oil and gas: sampling lines, gauge isolation and instrument tubing runs.
- Utilities and power: instrument air, steam sampling points and test connections.
- Water and desalination: chemical dosing and sample taps where the body material suits the fluid.
- Manufacturing and laboratories: flow setting on test rigs and small process lines.
Selection and compatibility notes for the 1711F4Y
Check five things before you order the 1711F4Y. First, the body material: 316 stainless steel must suit the process fluid and the environment. Second, the end connections: 1/4 inch female NPT inlet and 1/4 inch female NPT outlet must match your pipe or tubing, and GYROLOK ends need the matching tube size. Third, the stem tip: metal stem tip. Fourth, the pressure and temperature of your system against the ratings above. Fifth, any special cleaning, such as oxygen cleaning or helium leak testing, which the manufacturer says should be specified when ordering.
Other valves in the same order table that buyers often compare with the 1711F4Y are 1711M4Y, 1711L4Y, 1711G4Y and the Monel 1711F4M. The first four digits of the part number identify the series and stem tip, the letter after them identifies the end connections, the next digit the size and the final letter the body material.
The manufacturer notes that applications requiring TPED or PED certification can add a CE suffix to the part number, and that additional sizes and options are available on special request. Always state in the RFQ if you need such a variant rather than the standard 1711F4Y.
Installation and commissioning of the 1711F4Y
Install the 1711F4Y with the flow direction and orientation of your design, supporting the tubing so that no bending load acts on the valve body. For NPT connections use a thread sealant suitable for the fluid and tighten without over-torquing the body. For GYROLOK ends follow the tube fitting instructions for the tube size and wall thickness. Panel mounting uses the panel hole and nut described in the specification table.
During commissioning close the 1711F4Y fully but do not force the stem past the seat, then open slowly while the line is pressurised and check the stem packing and end connections for leakage. Because the globe pattern is a manual valve, operators should be trained to open it gradually to avoid sudden pressure steps on downstream instruments.
Maintenance of the 1711F4Y
Inspect the 1711F4Y at the regular intervals set for your plant. Look for weeping at the packing nut and end connections, a stiff stem, or loss of shutoff that suggests seat wear. The manufacturer publishes packing and seat replacement instructions for its needle valve series and states that spare parts and repair kits are available for all needle valves, so request the correct kit by series when the valve is serviced rather than discarding the body.
Keep a record of the full part number 1711F4Y, the installation date and the service fluid. This makes later spare part requests quicker and avoids ordering the wrong tip or packing style.
Related products and ordering notes
Seven Star LLC can quote the 1711F4Y together with other Hoke needle valves, tube fittings and instrument valves for the same project. For the 1700 series the related part numbers include 1711M4Y, 1711L4Y, 1711G4Y and the Monel 1711F4M. Give the exact part number, not only the series, because small differences in end connection or stem tip change the product.
All specifications on this page come from the manufacturer literature and may change, so confirm critical values with the current datasheet before purchase.
1711F4Y frequently asked questions in brief
The 1711F4Y is a 316 stainless steel globe pattern needle valve with 1/4 inch female NPT ends, rated for 6000 psig (414 bar) at 70 degrees F. It uses a metal stem tip for service up to 450 degrees F. The full question and answer list is below on this page, and the quotation steps are in the last section.
Documents and quotation
The manufacturer needle valve catalogue covering the 1700 series is available as a datasheet download on this page. To request a quotation, send an RFQ to Seven Star LLC with the part number 1711F4Y, the quantity, the delivery location and any cleaning or certification requirement. We reply with availability and lead time for Oman and the GCC.
Other Models in the Hoke 1700 Range
Seven Star LLC supplies models from the Hoke 1700 range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.
| Model | Category | |
|---|---|---|
| Hoke 1711M4Y Needle Valve, 1/4 in Male NPT, 316 SS | Instrument Valves & Fittings | View details |
| Hoke 1711G4Y Globe Needle Valve, 316 SS | Instrument Valves & Fittings | View details |
| Hoke 1711F4Y Globe Needle Valve, 316 SS | Instrument Valves & Fittings | You are viewing this model |
| Hoke 1711G6Y Globe Needle Valve, 316 SS | Instrument Valves & Fittings | View details |
| Hoke 1711M4M Globe Needle Valve, Monel | Instrument Valves & Fittings | View details |
| Hoke 1751M4Y Globe Needle Valve, 316 SS | Instrument Valves & Fittings | View details |
| Hoke 1751G4Y Globe Needle Valve, 316 SS | Instrument Valves & Fittings | View details |
Datasheets & Documents
- Datasheet Hoke 1711F4Y Needle Valve Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
Hoke is an instrumentation flow-control brand specializing in small-bore valves and fittings, part of Crane Instrumentation & Sampling. The range includes needle, ball, metering, plug and packless valves, double block and bleed and monoweld designs, Gyrolok tube fittings, instrumentation manifolds, quick couplings, and sampling cylinders with their valves and accessories. Hoke products are used wherever sample lines, gauges, transmitters and analyzers have to be isolated, vented or sampled cleanly across process industries. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. We help buyers match valve, fitting and sample cylinder part numbers to their tubing size, pressure rating and material requirements, so installations stay leak-tight and easy to maintain.
FAQ
Questions about the Hoke 1711F4Y Globe Needle Valve, 316 SS
Answers from our engineering team on installation, compatibility and integration.
01What is the Hoke 1711F4Y?
It is a 316 stainless steel globe pattern needle valve of the Hoke 1700 series with 1/4 inch female NPT inlet and 1/4 inch female NPT outlet connections and a metal stem tip.
02What pressure and temperature does the 1711F4Y handle?
The manufacturer lists 6000 psig (414 bar) at 70 degrees F (21 degrees C) and an operating temperature of minus 65 to plus 450 degrees F (minus 54 to plus 232 degrees C).
03What is the flow coefficient and orifice of the 1711F4Y?
The catalogue order table lists an orifice of 0.187 inch (4.7 mm) and a Cv of 0.45 for the 1711F4Y.
04Which similar part numbers should I compare with the 1711F4Y?
The same order table lists 1711M4Y, 1711L4Y, 1711G4Y and the Monel 1711F4M. Differences are in end connections, stem tip or body material.
05How do I request a quotation for the 1711F4Y?
Send an RFQ to Seven Star LLC with the part number 1711F4Y, the quantity and the delivery location in Oman or the GCC. Mention any oxygen cleaning or leak test requirement.


















Reviews
There are no reviews yet.