Tegera Chemforce 7350 Winter-Lined Nitrile Chemical Gloves

A warm nitrile chemical glove for cold rooms and outdoor wet work

Tegera Chemforce 7350 is a fleece-lined, fully dipped nitrile glove for people who handle chemicals and oils in the cold. Ejendals describes it as super soft, with a sandy finish that grips slippery tools and a 0.3 mm chemical protection layer. It is waterproof, oil and grease resistant, latex-free and approved for handling foodstuffs, so it moves between a process area and a cold store without a change of glove.

The glove is a Category III chemical protection glove and appears in the sheet under chemical protection gloves and cold insulation gloves. The construction is a layered one: an acrylic inner, a cotton middle layer and a nitrile outer, sold in blue at a 300 mm length that covers the wrist and lower forearm.

Key features

• Winter lining in fleece, with an acrylic inner and a cotton middle layer
• Nitrile outer with a sandy finish for grip on slippery tools
• Chemical protection layer of 0.3 mm
• Waterproof, water and oil repellent, oil and grease resistant
• Latex-free and approved for handling foodstuffs
• Warm, windproof and waterproof feature icons printed on the sheet
• Length 300 mm, dexterity level 5
• Chemical permeation and degradation data printed for five test chemicals

Technical specifications

Printed chemical test results (EN ISO 374-1:2016)

Sizes and article numbers

Reading the chemical data before you order

Type B in EN ISO 374-1 means the glove reached at least permeation level 2 (30 minutes) against at least three of the listed test chemicals; the sheet shows five, J K O P T, with level 6 (more than 480 minutes) for n-heptane, sodium hydroxide and formaldehyde and level 5 for hydrogen peroxide (general level table of the standard). Ammonia only reaches level 2, so do not choose this glove for prolonged ammonia exposure.

The chemical names behind the letters come from the EN ISO 374-1 list and are general information. The sheet refers to EN 16523-1:2015 for chemical resistance and asks you to contact Ejendals for details on other substances. If your process fluid is not in the table, request the manufacturer data before you order. Only four sizes are listed, 8 to 11, so confirm that M to XXL covers your crew.

Cold, wet and oily conditions

The EN 388 result 3121X gives abrasion 3, cut 1, tear 2 and puncture 1, which is typical for a nitrile dip and tells you not to rely on the glove around sharp edges. Wear it only for the hazards that are printed. The warm lining makes it a winter or cold-store glove; in hot yards, wet-hand sweat inside a lined glove is a comfort issue, so plan breaks.

After use, rinse chemical residues from the outside before taking the glove off, let it dry in air and away from heat, and discard it after contact with a substance that is not in the test table or when the nitrile cracks or swells.

Applications on oil, gas and chemical sites

The sheet lists painting, construction, concrete work, marine work, petro-chemical work, paper industry, food handling and chemical work, with oil and gas extraction, chemical and petrochemical, and mining and quarrying as industries. The environments printed include corrosive, wet, oily and greasy, cold and microbiological risk. That combines well with solvent handling, tank cleaning, catering stores and cold-room maintenance.

Selection and care notes

Chemical gloves must be matched to the chemicals present. The data sheet lists the tested substances and the performance levels, so compare them with the safety data sheets of the products handled on site. Inspect the glove for cuts, swelling or stiffness before each use, replace it after contact with a substance for which it is not rated, and wash and dry it as the care instructions describe. The fleece lining is meant for cold work, so choose a lighter glove for hot areas.

Information needed for a quotation

Send the glove size range, the quantity in pairs, the chemicals handled, the delivery location in Oman or the GCC and any other protective equipment, so that the complete supply can be quoted together.

Documents and supply information

The manufacturer data sheet is attached to this page and should be read together with the project specification before a purchase is confirmed. Filter class, airflow, pressure drop and dimensions are quoted as printed on that sheet. Lead time, stock position and certificates available with the shipment are confirmed in the quotation, and we supply to Oman and the wider GCC region for industrial, utility and building services projects.

Related items and documents

For hot chemical work compare the Tegera 8160 latex glove, which is rated for contact heat up to 250 C, and for general-purpose cut protection see the Tegera 8855. Related protective equipment is grouped under Safety & PPE. The product sheet is attached as a PDF; confirm sizes and chemicals against your own risk assessment before you order from Seven Star LLC, an independent supplier in Muscat.

Frequently asked questions

Is Tegera Chemforce 7350 lined?

Yes. It is winter-lined with fleece, over an acrylic inner and a cotton middle layer, with a nitrile outer.

Which chemicals is it tested against?

The sheet prints EN ISO 374-1 Type B with the letters J, K, O, P and T and gives permeation and degradation values for each.

Is it approved for food contact?

The sheet lists it as approved for handling foodstuffs and as latex-free.

How thick is the chemical layer?

The chemical protection layer is 0.3 mm; the total glove is a layered construction.

How long is the glove?

The length is 300 mm. Sizes 8 (M), 9 (L), 10 (XL) and 11 (XXL) are listed.