Liper LPUF-200BS01 IP65 Slim LED High Bay Light
Overview
The Liper LPUF-200BS01 is a slim-profile, IP65-rated LED high bay light from Liper Elektro GmbH’s BS Series, engineered for warehouses, factories, workshops, and other large industrial spaces with high ceilings. Rated at 200W and producing between 22,000 and 20,250 lumens, the fixture is also available in 150W and 300W variants (LPUF-150BS01 and LPUF-300BS01) within the same 385 x 120 mm ultra-thin die-cast aluminum housing, giving facility engineers a single product family to standardise across different bay heights and lighting loads.
Working closely with plant engineers in the region, Seven Star LLC proudly supplies the Liper LPUF-200BS01 high bay light and the wider Liper industrial and commercial lighting range to facility managers, contractors, and MEP consultants across Oman and the wider GCC. Buyers in Muscat, Sohar, Salalah, and other industrial zones can source genuine Liper LED lighting through Seven Star LLC with full CE and CB documentation, technical datasheets, and local after-sales support.
Operating Principle
The Liper LPUF-200BS01 uses a driver-on-board configuration, in which the LED driver is mounted directly within the fixture body rather than in the elevated dome commonly used on conventional high bay lights. This addresses a well-documented failure mode in industrial lighting: warehouses with iron-sheet roofing routinely see ambient temperatures near the ceiling exceed 100 degrees Celsius, and drivers mounted on the upper side of a fixture suffer accelerated thermal degradation because hot air naturally rises into that location. By relocating the driver and pairing it with an ultra-thin die-cast aluminum body engineered for heat dissipation, the LPUF-200BS01 is designed to maintain component temperature rise within validated limits even after extended operation in a 55-degree Celsius test environment.
Light distribution is handled through a specialised lens with an 80-degree beam angle, producing a long-throw, high-intensity, low-glare illumination pattern suited to tall industrial ceilings, with an optional aluminum reflector available for applications requiring a narrower, more directed beam onto the working floor. The result for facility operators is consistent, flicker-free illumination without the premature dimming or driver failures that shorten the service life of lower-grade high bay fixtures in hot, dusty, or humid industrial environments.
Engineering Design of the Liper LPUF-200BS01
The Liper LPUF-200BS01 is built around a 385 x 120 mm ultra-thin die-cast aluminum body that keeps the fixture compact and lightweight while still providing sufficient surface area for passive heat dissipation. The IP65 ingress protection rating allows the fixture to be installed in dry, humid, or wet locations without additional enclosures, making it suitable for both fully enclosed warehouses and semi-open industrial structures exposed to dust and moisture. Selectable colour temperatures of 2700K, 4000K, and 6500K allow the same fixture family to be specified for warm-tone hospitality-adjacent storage areas or cool, high-visibility factory floors.
Installation is designed around speed and safety: each unit ships with a 50cm safety hanging chain that stabilises the fixture during and after mounting, and Liper documents a typical installation time of around three minutes per fixture, reducing the labour cost and ceiling-access downtime associated with high-bay retrofits. The fixture carries CE and CB certification and an IES file is available for lighting designers who need to model illuminance levels before specifying quantities and mounting heights for a given facility layout.
Key Features
The Liper LPUF-200BS01 high bay light combines a driver-on-board thermal design with industrial-grade ingress protection, making it a dependable choice for high-heat, high-ceiling facilities across the GCC:
- Liper LPUF-200BS01 delivers 200W rated power and 22,000–20,250 lumens, with LPUF-150BS01 and LPUF-300BS01 variants sharing the same platform.
- IP65 ingress protection suitable for dry, humid, and wet indoor or outdoor industrial locations.
- Driver-on-board design that avoids the premature failures common to top-mounted drivers in hot ceiling environments.
- Ultra-thin die-cast aluminum body engineered for efficient passive heat dissipation.
- Selectable colour temperatures of 2700K, 4000K, and 6500K to match different facility requirements.
- 80-degree beam angle lens for broad, low-glare illumination, with an optional narrower-throw aluminum reflector.
- Rated 50,000-hour service life backed by CE and CB certification.
- Fast, tool-light installation using an included 50cm safety hanging chain, typically under three minutes per fixture.
Industrial Applications
The Liper LPUF-200BS01 is designed for large-area industrial and commercial lighting, including warehouses, manufacturing plants, workshops, garages, storage facilities, gymnasiums, and supermarket or exhibition-hall interiors where ceiling heights make lamp replacement costly and disruptive. In the GCC, where ambient temperatures already push metal-roofed warehouse interiors into extreme heat for much of the year, the driver-on-board thermal design is particularly relevant to logistics parks, cold-chain distribution centres, and light manufacturing facilities that cannot tolerate frequent lighting outages.
With fast quotation turnaround and technical support, Seven Star LLC distributes the LPUF-200BS01 and the broader Liper high bay, floodlight, and panel light ranges to industrial facilities, logistics operators, and commercial developments throughout the Sultanate of Oman and the wider GCC, including projects around the Sohar and Salalah economic zones. Whether the requirement is a full warehouse retrofit built around the Liper LPUF-200BS01 or a phased rollout across multiple sites, Seven Star LLC’s supply on request and technical support help facility teams standardise on a single certified lighting platform.
Technical Specifications
Key technical parameters for the Liper LPUF-200BS01 IP65 slim high bay light are summarised below, covering the full LPUF-200BS01 specification set that facility engineers need for layout planning.
| Parameter | Specification |
|---|---|
| Model | Liper LPUF-200BS01 (BS Series) |
| Rated Power | 200W (150W and 300W variants available) |
| Luminous Flux | 22,000–20,250 lumens |
| Colour Temperature | 2700K / 4000K / 6500K |
| Ingress Protection | IP65 |
| Body Material | Ultra-thin die-cast aluminum |
| Product Size | 385 x 120 mm |
| Rated Lifespan | 50,000 hours |
| Beam Angle | 80° (optional narrower-throw aluminum reflector available) |
| Dimming | Non-dimmable (standard) |
| Certification | CE, CB |
| Mounting | Ceiling suspension with 50cm safety hanging chain |
Request a Quote for Liper LPUF-200BS01 IP65 Slim LED High Bay Light
Facility managers, MEP contractors, and procurement teams in Oman and across the GCC can request a formal RFQ for the Liper LPUF-200BS01 IP65 slim high bay light directly from Seven Star LLC, and the LPUF-200BS01 datasheet is available on request. With engineering support in Muscat, Seven Star LLC supplies on request, provides technical datasheets and IES files on request, and connects buyers with the lighting and electrical division for fixture selection, layout planning, and site-wide rollout support. Contact Seven Star LLC today to confirm wattage, colour temperature, and delivery to your facility in Muscat, Sohar, Salalah, or anywhere in the Sultanate of Oman.
Related Products
- Schneider Electric EasyPact CVS Molded Case Circuit Breaker
- Schneider Electric Fupact Fuse Switch Disconnector
- Schneider Electric Masterpact MTZ1 Air Circuit Breaker
- Schneider Electric PowerLogic P5 Feeder Protection Relay
- Crompton Greaves 615923 Porcelain Bushing 17.5 kV
- ABB AC 800F Power Supply Module SA 811F (3BDH000013R1)
The Liper LPUF high bay light
The listing describes a slim, round high bay luminaire rated IP65. Under the IEC ingress protection code, the first digit 6 means dust-tight and the second digit 5 means protected against water jets, which suits dusty stores and areas that are hosed down. Power, lumen output, color temperature and beam angle should be read from the Liper datasheet for the exact model code.Ordering Liper lighting: what we need
Send the full model code, the quantity, the mains voltage, the color temperature you want and the mounting method, hook or bracket. For a new area, add the mounting height and floor dimensions.Browse Liper products by category: Electrical & Power Modules.
Reviews
There are no reviews yet.