Brand:

Cortem ST-59.1 3-Entry Ex d IIC Junction Box

Description

Cortem ST-59.1 product summary

The Cortem ST-59.1 listing describes a three-entry size 9 Ex d IIC aluminium junction box with 1 1/2 inch entries. This box has three 1 1/2 inch entries in a size 9 body with A = 190 mm, D1 = 146 mm and H = 105 mm. According to the manufacturer sheet it is marked II 2GD Ex d IIC T… Gb / Ex tb IIIC T… Db, IP66/67 (also Ex e and Ex i versions) and certified under ATEX CESI 03 ATEX 059U (empty) and CESI 02 ATEX 091 (with terminals), IECEx CES 15.0012U.

Seven Star LLC works as an independent supplier for Oman and the GCC and is not affiliated with the manufacturer. The values quoted here are summarised from the published data sheet, so check the current edition at order time.

What stands out on this unit

  • Three entries of 1 1/2 inch
  • Size 9 body with 105 mm height
  • Screw-on lid with grub screw
  • Stainless steel bolts and earth screws
  • Choice of thread standard on request

Cortem ST-59.1 technical specifications

Part number ST-59.1
Series S.1 aluminium Ex d IIC junction boxes
Entries (GAS UNI ISO 7/1) 3 x 1 1/2″
Model B
Outside A x D1 x H 190 x 146 x 105 mm
Chart columns C / B1 / Ød1 60 mm / 30 mm / 130×2 mm
Chart columns S / S1 4 / 7
Marking II 2GD Ex d IIC T… Gb, Ex tb IIIC T… Db, IP66/67
Certificates CESI 03 ATEX 059U (empty); CESI 02 ATEX 091; IECEx CES 15.0012U; CES 14.0018X
Ambient range -40°C to +150°C empty; -40°C to +40°C with terminals as standard
Rated voltage and frequency 750 V; 50/60 Hz
Terminal sizes and current 1.5 to 70 mm2; 8 to 175 A
Max terminals 1.5 mm2: 16; 2.5 mm2: 16; 4 mm2: 16; 6 mm2: 9; 10 mm2: 7; 16 mm2: 6; 25 mm2: 4
Body and lid Low copper aluminium alloy, screw-on lid with safety grub screw
Gasket Silicone between body and lid
Screws and earth Stainless steel, earth screws inside and outside

How ST-59.1 differs from other S.1 variants

The table below shows where ST-59.1 sits against its siblings in the S.1 family. Dimensions, weight, capacity and the numbers of entries all change from one code to the next, so the code you order matters.

  • Three entries, whereas SC-59.1 has two entries of the same 1 1/2 inch size.
  • 1 1/2 inch entries against 3/4 inch on ST-29.1.
  • A = 190 mm, longer than the 100 mm of ST-26.1.
  • Terminal capacity 16 x 4 mm2, against 6 for ST-26.1.

Use cases across the Gulf

A Cortem ST-59.1 installation typically supports an Omani or Gulf plant that needs hazardous-area wiring points: upstream, midstream and downstream oil and gas, fuel depots, utilities, and industrial production halls. Three large entries make it a branching point where a trunk cable and two feeders meet, such as at a pump motor terminal run or a lighting circuit in a process area. The family literature highlights refineries, chemical plants, onshore and offshore sites and fuel depots as typical settings.

Choosing ST-59.1: compatibility

Before you specify Cortem ST-59.1, compare three things: the zone and gas or dust group against II 2GD Ex d IIC T… Gb / Ex tb IIIC T… Db, IP66/67 (also Ex e and Ex i versions), the ambient temperature window (-40°C to +150°C for the empty box and -40°C to +40°C as standard with terminals), and the space you need inside. Capacity is the size 9 group: 16 terminals up to 4 mm2, 9 of 6 mm2, 7 of 10 mm2, 6 of 16 mm2 and 4 of 25 mm2. Entries have to use fittings certified to the same standards as the box, and unused holes must be closed with certified plugs.

Installation and maintenance guide

Mounting ST-59.1 is simple if the fixings are laid out first: use the listed centres, take the earth bond from the dedicated screw, and torque the cover bolts in a cross pattern. Close all unused entries with certified plugs, because three large threaded openings are easy to forget; fit gaskets on the glands. Finish with insulation testing, a check that every unused entry is closed with a certified plug, and a signed inspection record.

Routine care for ST-59.1 is light: look over the coating and gasket during planned inspections, keep the joint surfaces clean and undamaged, and re-tighten cover screws that have been disturbed. Look at the three entries for corrosion and loosened glands and check the lid gasket after thermal cycling. Never paint the flame or sealing surfaces and never modify the enclosure outside what the certificate allows.

Related products, ordering and FAQ summary

Companion parts for Cortem ST-59.1 include Ex certified glands, closing plugs, earth accessories and, where the data sheet allows, windows or breather and drain valves. State the accessories and entry layout in your RFQ so the quotation covers the complete assembly.

Treat the code ST-59.1 as the whole order specification: it fixes the size, the entry layout and the family. When you replace a unit, check the old nameplate, the fixing pattern and the certificate number, then confirm them against the data above; the marking to match is II 2GD Ex d IIC T… Gb / Ex tb IIIC T… Db, IP66/67 (also Ex e and Ex i versions).

In short, ST-59.1 is the three-entry size 9 box; the FAQs cover entries, size, terminals, stainless options and ordering.

Documents and quotation

A datasheet PDF for Cortem ST-59.1 is provided with this listing. For pricing and lead time, email the RFQ stating ST-59.1, the quantity required and the project location in Oman or the GCC; add the certificate or option details if they matter.

Selection Notes for the Cortem ST-59.1

When comparing the Cortem ST-59.1 with alternatives, start from the duty it must perform: the measured or controlled variable, the range and accuracy you need, the environment at the mounting point and the interface to your control system. Check the electrical and mechanical connections against the installed equipment, and confirm any hazardous-area or ingress-protection requirements for the location. If any point is unclear, send a photo of the nameplate and a short description of the application, and we will compare it with the Cortem switchgear, enclosures & distribution range and confirm the correct order code before you commit.

Other Models in the S.1 Range

Seven Star LLC supplies models from the S.1 range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Cortem ST-59.1 3-Entry Ex d IIC Junction BoxSwitchgear, Enclosures & DistributionYou are viewing this model
Cortem SC-26.1 Ex d IIC Junction Box 3/4 inSwitchgear, Enclosures & DistributionView details
Datasheets & Documents
  • PDF Datasheet Cortem ST-59.1 3-Entry Ex d IIC Junction Box Datasheet Download
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Cortem is the Italian maker of explosion-proof and increased-safety electrical equipment: Ex d and Ex e lighting, enclosures, control stations, plugs and sockets, cable glands and signalling devices. Marco Rossi and Renato Gratton founded the company on 24 February 1968 in Villesse, in the Friuli Venezia Giulia region of north-east Italy. Cortem S.p.A. heads the Cortem Group, which also includes Elfit and the Fondisonzo foundry, and supplies onshore and offshore oil and gas, chemical and industrial plants.

Seven Star LLC is an independent supplier in Muscat. We list Cortem junction boxes, lighting, plugs and sockets and control stations for oil and gas and process projects in Oman and the GCC.

Cortem company profile

Founded 24 February 1968, Villesse (Gorizia), Italy
Founders Marco Rossi and Renato Gratton
Name From the Italian for electromechanical construction and technical representation
Group companies Cortem S.p.A., Elfit and Fondisonzo
Approvals ATEX and IECEx certified explosion-protected equipment
Product families Ex d and Ex e luminaires and LED fittings, emergency and exit lights, obstruction lights, junction and control boxes, control stations, plugs and sockets, cable glands, alarm and signalling devices

Milestones

  • 1968: Marco Rossi and Renato Gratton found Cortem in Villesse on 24 February.
  • 2011: Research and development on LED lighting for hazardous areas begins.
  • 2012: The first Cortem LED fixture series is launched.
  • 2022: The third generation of Cortem LED fixtures is released.

Cortem product series

Enclosures include the EJBX stainless steel Ex d junction boxes, EJBC aluminium Ex d boxes for gas group IIC, the SA and SAG Ex eb aluminium boxes in 18 sizes and the EJBE and EJBXE Ex de control and distribution boards. Control and power connection products include the CMD Ex e fibreglass control stations and the PYN, SPYN and CMBSP07 Ex plugs and sockets from 16 to 125 A.

Lighting covers the SLED-ME and EVL-40 Ex LED floodlights, the Ex nR SLED-MN and EVNL-40 floodlights for zone 2, the LIFEX-M linear fixture, the FLOWEX high bay, the EVML low bay, STREETEX street lighting and the XLFE-LIB and XLFE-MIA obstruction lights for stacks and towers. The GRDE-4200 is an electronic earthing system for road tanker loading bays.

Where Cortem equipment is used

Refineries, gas plants, tank farms and loading terminals, offshore platforms and ships, chemical and pharmaceutical plants and mining. Products are certified to ATEX and IECEx, with other schemes according to model.

Cortem products we list

Family Examples
Automation Accessories CMBSP07 Ex GRP Plugs and Sockets 16 A to 125 A, CMD Ex e Fibreglass Control and Signalling, EJBC Aluminium Ex d Junction Boxes for Gas, EJBE-EJBXE Ex de Control and Distribution, EJBX Stainless Steel Ex d Junction Box IIB+H2, EV Ex d Luminaires for Traditional and LED, EVL-40 Ex LED Floodlight with 40 Degree Beam, EVML Ex LED Low Bay Luminaire and 14 more

Ordering Cortem products: what we need

Send the model code, the zone and gas or dust group, temperature class, ingress protection, the certification scheme required, and for enclosures the size, entries and internal components. For lighting give the wattage, voltage and mounting; for plugs and sockets the current, poles and voltage.

Facts checked against Cortem Group's published company history, October 2026.

FAQ

Questions about the Cortem ST-59.1 3-Entry Ex d IIC Junction Box

Answers from our engineering team on installation, compatibility and integration.

01How many entries does Cortem ST-59.1 have?
Three entries of 1 1/2 inch GAS UNI ISO 7/1.
02What size is Cortem ST-59.1?
A = 190 mm, D1 = 146 mm and H = 105 mm. This applies to part number ST-59.1 as listed in the manufacturer data sheet.
03How many terminals fit in Cortem ST-59.1?
Up to 16 terminals of 1.5, 2.5 or 4 mm2 and 4 of 25 mm2.
04Does Cortem ST-59.1 come in stainless steel?
The sheet lists AISI 316L versions on request.
05How do I order Cortem ST-59.1?
Send an RFQ with ST-59.1 and quantity. This applies to part number ST-59.1 as listed in the manufacturer data sheet.