- Automation & ControlView all 2,858 products
- Automation Accessories
- AC Drives
- PLC & I/O Cards
- Industrial Communications
- Vibration Monitoring
- Controllers & Data Acquisition
- Isolator & Barrier
- Safety Switches & Guard Locking
- Motor Soft Starters
- CCTV & Security
- Encoders
- Pneumatic Cylinders
- HMI Displays
- Servo Drives
- Industrial Computers
- Machine Vision
- Automation Software
- Robotics
Brand: KRACHT
KRACHT KP 3/71 V20G W00 6DL2 High-Pressure Gear Pump
Description
KRACHT KP 3/71 V20G W00 6DL2 overview
KRACHT KP 3/71 V20G W00 6DL2 is a high-pressure external gear pump from the KRACHT KP 3 range with a geometric displacement of 70.6 cm3 per revolution, a sustained operating pressure of 230 bar and a peak pressure of 280 bar.
Within the KP 3 series this variant sits at nominal size 71. It supplies 96.6 l/min at 210 bar when turned at 1450 rpm in mineral oil of 34 mm2/s, which is 94.4 percent of its theoretical 102.4 l/min.
Its type code reads as follows: size 71, mounting by SAE-C 4-hole flange (code V), anticlockwise rotation, housing connection G, shaft end W, FKM seals. Every letter of KP 3/71 V20G W00 6DL2 therefore maps to a physical feature that you can verify on the nameplate before the unit is mounted.
Key features of KP 3/71 V20G W00 6DL2
- Axial play is compensated by hydraulically loaded sliding plates, independent of viscosity, so volumetric and mechanical efficiency stay high at every operating point
- Continuous pressure rating of 230 bar and peak rating of 280 bar for this pump
- Shaft end code W (external spline B 28 x 25 to DIN 5482, z = 15, m = 1.75) transmits up to 450 Nm, whereas the unit at 210 bar and 1450 rpm calls for approximately 262 Nm
- Tooth profile with 14 teeth plus a special expansion-groove layout in the quench oil area reduces flow ripple and pressure pulsation, which lowers machine noise
- Rotation anticlockwise as coded in the type code, with the flow direction running left to right when the shaft turns clockwise as seen on the shaft end
KP 3/71 V20G W00 6DL2 technical specifications
| Parameter | Value for KP 3/71 V20G W00 6DL2 |
|---|---|
| Shaft seal | FKM rotary shaft lip-type seals (medium up to 150 degrees C) |
| Ports | housing connection G, suction SAE 1 1/2 inch (40 mm) and pressure SAE 1 1/4 inch (32 mm) |
| Maximum operating pressure (outlet) | 230 bar (S1/S3 duty, viscosity 30 mm2/s or more, 1000 rpm or more) |
| Geometric displacement | 70.6 cm3 per revolution |
| Shaft end | external spline B 28 x 25 to DIN 5482, z = 15, m = 1.75, code W, permissible torque 450 Nm |
| Rotation sense | anticlockwise (code 2), viewed on the drive shaft end |
| Highest speed | 2500 rpm |
| Ambient range | -20 to 60 degrees C |
| Ordering code | KP 3/71 V20G W00 6DL2 |
| Gear design | case-hardened steel, ground tooth flanks, 14 teeth (code L) |
| Inlet pressure range | -0.4 bar (vacuum) up to 2 bar; 5 bar for short periods |
| Manufacturer | KRACHT GmbH, Werdohl, Germany |
| Peak pressure | 280 bar |
| Recommended oil cleanliness | ISO 4406 code 21/19/16 (NAS 1638 class 10) |
Flow, power and lowest speed of KP 3/71 V20G W00 6DL2
| Pressure (bar) | 20 | 60 | 100 | 140 | 180 | 200 | 210 |
|---|---|---|---|---|---|---|---|
| Flow at 1450 rpm (l/min) | 100.1 | 99.4 | 98.7 | 98.0 | 97.2 | 96.8 | 96.6 |
| Input power at 1450 rpm (kW) | 4.10 | 11.63 | 19.15 | 26.68 | 34.20 | 37.96 | 39.84 |
| Pressure (bar) | 20 | 60 | 100 | 140 | 180 | 200 | 210 |
|---|---|---|---|---|---|---|---|
| Flow at 950 rpm (l/min) | 64.8 | 64.1 | 63.4 | 62.7 | 61.9 | 61.5 | 61.3 |
| Input power at 950 rpm (kW) | 2.68 | 7.61 | 12.54 | 17.47 | 22.40 | 24.87 | 26.10 |
| Pressure up to (bar) | 100 | 120 | 150 | 180 | 200 |
|---|---|---|---|---|---|
| Minimum speed (rpm) | 700 | 700 | 800 | 900 | 900 |
Because the catalogue specifies volumetric efficiency of about 0.95 and total efficiency of about 0.90 at the nominal point, a quick check for this pump returns a delivery of around 97.3 l/min at 1450 rpm, which agrees with the tabulated figures within a few percent.
Reading the 1450 rpm row: output decreases from 100.1 l/min at 20 bar to 96.6 l/min at 210 bar, a loss of 3.5 percent, whilst input power climbs from 4.10 kW to 39.84 kW. Add 20 percent, as the catalogue advises, and the motor for this pump should be about 47.8 kW at the top point.
How KP 3/71 V20G W00 6DL2 differs from further KP 3 variants
Within the KRACHT KP 3 series the nominal sizes run 63, 71, 82, 100, 112, 125. Displacement grows with the size, so this pump with 70.6 cm3 per revolution is a fixed point on that ladder rather than a universal pump.
The next smaller size, 63, has 62.5 cm3 per revolution and a 230 bar rating, so this pump shifts about 8.1 cm3 more oil per turn and functions at a sustained 230 bar, which is the same as size 63.
The next larger size, 82, offers 81.0 cm3 per revolution and 210 bar, which means KP 3/71 V20G W00 6DL2 gives up 10.4 cm3 of displacement in exchange for 20 bar more continuous pressure.
Beyond size, KP 3/71 V20G W00 6DL2 is distinguished by its code letters: flange V, rotation anticlockwise, housing G, shaft end W and FKM. Changing any one of these letters creates a different orderable pump, even though the unit body is the same.
Against the KP 2 series, a KP 3 pump including KP 3/71 V20G W00 6DL2 uses SAE-C 2-hole or 4-hole flanges and starts at 62.5 cm3 per revolution, whereas KP 2 ends at 61.2 cm3 and uses smaller flanges.
Typical applications of KP 3/71 V20G W00 6DL2 in Oman and the GCC
Utilities and power stations use this class of external gear pump in turbine-hall hydraulic packs and valve actuation skids, usually run from a 4-pole or 6-pole motor at around 1450 or 950 rpm, which are precisely the speeds the data sheet tabulates.
Mobile and workshop equipment in the region, including service rigs and maintenance trolleys, can use KP 3/71 V20G W00 6DL2 as a replacement for a worn pump of the same flange V and shaft end W.
The data sheet lists mineral oil to DIN 51524/25 and engine oil to DIN 51511 as standard media, with flame-retardant liquids available on request, so site medium choice should be confirmed before this pump is quoted for a plant.
Selection and compatibility notes for KP 3/71 V20G W00 6DL2
Check that the liquid viscosity stays between 10 and 600 mm2/s and ideally between 30 and 45 mm2/s; at start-up with cold oil the pump calls for the lowest speed of 700 rpm shown for the working pressure.
Recommended filtration is a filter with beta 25 of 75 up to 300 bar or beta 40 of 75 up to 100 bar, and the target cleanliness is ISO 4406 code 21/19/16.
Select the motor from the table: 39.84 kW at 210 bar and 1450 rpm plus the 20 percent reserve the catalogue recommends yields 47.8 kW for this pump.
Installation and commissioning of KP 3/71 V20G W00 6DL2
Install KP 3/71 V20G W00 6DL2 on its SAE-C 4-hole flange (hole spacing 114.55 mm, centring diameter 127 mm) so that the centring spigot sits square in the drive bell; mounting position of the unit is free, but keep the shaft end free of axial thrust.
Keep the ambient temperature between -20 and 60 degrees C and the liquid below 150 degrees C, which is the limit of the FKM shaft seals fitted to KP 3/71 V20G W00 6DL2.
Install a pressure relief valve on the delivery line sized for the full 100.1 l/min the unit can deliver at 1450 rpm, set no higher than the 230 bar permanent rating.
Maintenance and service for KP 3/71 V20G W00 6DL2
Keep a record of the name plate and ordering code KP 3/71 V20G W00 6DL2 so that spares are matched by flange V, shaft end W and rotation anticlockwise rather than by size alone.
Replace the FKM shaft seal if oil appears at the shaft end; the catalogue gives 150 degrees C as the upper liquid limit for that seal material.
KP 3/71 V20G W00 6DL2 FAQ summary
What displacement does KRACHT KP 3/71 V20G W00 6DL2 have? this pump has a geometric displacement of 70.6 cm3 per revolution, giving 102.4 l/min theoretical flow at 1450 rpm and 96.6 l/min tabulated at 210 bar.
What pressure can this pump withstand? The permanent operating pressure at the outlet is 230 bar with a peak of 280 bar, valid for viscosity of 30 mm2/s or more and speeds from 1000 rpm.
Which shaft end and flange does KP 3/71 V20G W00 6DL2 have? Shaft end code W is described as: external spline B 28 x 25 to DIN 5482, z = 15, m = 1.75, rated at 450 Nm. Flange code V is described as: SAE-C 4-hole flange (hole spacing 114.55 mm, centring diameter 127 mm).
Documents and quotation
For KP 3/71 V20G W00 6DL2 the matching documentation is the KRACHT KP 2 / KP 3 high-pressure gear pump data sheet, published as a PDF here, with the type key, technical data, flow and power tables and dimension sheets.
Please include KP 3/71 V20G W00 6DL2, the required quantity and the destination country in your RFQ; if you hold the old unit, add a picture of its type plate.
Please note that Seven Star LLC is an independent supplier serving Oman and the GCC, not affiliated with the manufacturer.
Datasheets & Documents
- Datasheet KRACHT KP 3/71 V20G W00 6DL2 High-Pressure Gear Pump Datasheet Download
Reviews (0)
How would you rate this product? Cancel reply
About brand
KRACHT is the German maker of gear pumps, gear flow meters, hydraulic valves, motors and cylinders. The company was entered in the trade register in 1911 as Hillebrand & Kracht OHG and is based in Werdohl, in the Sauerland region of Germany. For most of its history it was a medium-sized family company; in January 2024 it became part of the Atlas Copco Group, in the Power and Flow division.
Seven Star LLC lists KRACHT pumps, flow meters, valves and hydraulic motors, and sources them by type key for machinery and marine users in Oman.
KRACHT company profile
| Founded | 1911, registered as Hillebrand & Kracht OHG |
|---|---|
| Headquarters | Werdohl, North Rhine-Westphalia, Germany; in today's premises since 1971 |
| Ownership | Atlas Copco Group since January 2024 (Power and Flow division, Power Technique business area); previously a family company |
| Size | About 440 employees and revenue of about EUR 72 million in 2022, as reported by Atlas Copco |
| Subsidiaries | USA, China and Hungary (KRACHT Hidraulik Kft.) |
| Product families | External gear pumps for lube oil, fuel and process duty, VC and VZ gear flow meters, pressure and flow control valves, hydraulic motors and cylinders |
Milestones
- 1911: Hillebrand & Kracht OHG is entered in the trade register.
- 1971: The company moves into its present premises in Werdohl.
- 1992: A gear manufacturer in Hungary is acquired, today KRACHT Hidraulik Kft.
- 2023–2024: Atlas Copco agrees to buy KRACHT in December 2023 and completes the deal in January 2024.
KRACHT pumps, flow meters and valves listed
The listing follows four product groups, pumps, fluid measurement, valves and drives:
- Pump technology: KF gear pumps for transfer of lubricating and other fluids, the KF-F version for fuels, and KP high pressure gear pumps
- Fluid measurement technology: gear type flow meters such as the VCA in aluminum
- Valve technology: SPV and SPVF pressure relief valves, the DBD directly controlled poppet valve, HV and HVF pilot operated valves and the DV B hydraulically pilot controlled valve
- Drive technology: KM hydraulic gear motors
Where KRACHT equipment is used
KRACHT equipment serves the marine, renewable energy, process technology and hydraulics industries. In practice that means lube oil and fuel oil transfer on engines, gearboxes and compressors, oil supply units, and metering of oils, resins, paints and other viscous media with gear flow meters in dosing and test bench systems. Enquiries from the GCC are mostly for a KRACHT pump or valve fitted to an imported machine or a ship's auxiliary system.
KRACHT products we list
Ordering KRACHT parts: what we need
KRACHT products carry a type key on the nameplate that encodes size, direction of rotation, shaft end, housing and seal material, connections and special numbers. An example from this page is SPV 10 L1G 1 A 12. Send the complete key and the serial or order number shown with it. If the plate is damaged, send the fluid and viscosity, flow rate, operating pressure and temperature, drive speed, port type and size, and photos with main dimensions. For KRACHT flow meters add the measuring range and the pickup or electronics required. We compare the key with KRACHT documentation and supply the manufacturer's data sheet on request.
Frequently requested KRACHT models: KRACHT Pump Technology Series.
Facts checked against KRACHT company literature and Atlas Copco's acquisition announcements, October 2026.
Browse KRACHT products by category: Safety Relief Valves, Pumps, Flowmeters, Electromotors.
FAQ
Questions about the KRACHT KP 3/71 V20G W00 6DL2 High-Pressure Gear Pump
Answers from our engineering team on installation, compatibility and integration.
01What displacement does KRACHT KP 3/71 V20G W00 6DL2 have?
KP 3/71 V20G W00 6DL2 has a geometric displacement of 70.6 cm3 per revolution, giving 102.4 l/min theoretical flow at 1450 rpm and 96.6 l/min tabulated at 210 bar.
02What pressure can KP 3/71 V20G W00 6DL2 withstand?
The continuous operating pressure at the outlet is 230 bar with a peak of 280 bar, valid for viscosity of 30 mm2/s or more and speeds from 1000 rpm.
03Which shaft end and flange does KP 3/71 V20G W00 6DL2 have?
Shaft end code W is described as: external spline B 28 x 25 to DIN 5482, z = 15, m = 1.75, rated at 450 Nm. Flange code V is described as: SAE-C 4-hole flange (hole spacing 114.55 mm, centring diameter 127 mm).
04Which direction does KP 3/71 V20G W00 6DL2 rotate?
Code 2 in the ordering code means anticlockwise rotation seen on the drive shaft end; running it the opposite way can damage the shaft seal and reverses flow.
05What motor power is needed for KP 3/71 V20G W00 6DL2?
At 210 bar and 1450 rpm the table shows 39.84 kW; with the 20 percent reserve recommended by the datasheet, plan about 47.8 kW.


















Reviews
There are no reviews yet.