Brand:

Luxfer HSSC20-1BA 316L Stainless Sample Cylinder 300 cc

Description

Luxfer HSSC20-1BA sample cylinder overview

The Luxfer HSSC20-1BA is a standard sampling cylinder in the 1,800 psi DOT range of the Luxfer sampling line. It holds 300 cc, is made from 316L stainless steel and carries the DOT-3E specification with a service pressure of 124 bar, which is 1800 psi. The manufacturer describes its sampling cylinders as a solution for a wide array of sample collection and analysis needs, and notes that tens of thousands are in use around the world in petrochemical refineries and well sites, analytical laboratories, alternative fuel technologies and manufacturing. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer.

A sampling cylinder is a small pressure vessel used to take a representative sample of gas or liquid at a process point and carry it safely to a laboratory or analyser. The Luxfer HSSC20-1BA is a compact vessel of 51 mm diameter and 235 mm length, which makes it easy to carry and store, while the 300 cc volume gives enough sample for most laboratory analysis routines.

Key features of the HSSC20-1BA

  • 316L stainless steel construction, listed by the manufacturer as the material for the whole 1,800 psi standard range.
  • DOT-3E specification with a service pressure of 124 bar (1800 psi).
  • Water volume of 300 cc, equal to 18 cubic inches.
  • Compact envelope of 51 mm diameter by 235 mm length, with a weight of 0.8 kg.
  • Thread size of .250-18 NPT, in other words a 1/4 inch NPT port.
  • No accessories included, so the buyer can choose valves and fittings to match the sampling system.

HSSC20-1BA technical specifications

The table gives the data that the manufacturer publishes for the HSSC20-1BA in its DOT 1,800 psi type 1 cylinder table, in both metric and imperial units.

Part number HSSC20-1BA
Brand Luxfer
Specification DOT-3E
Service pressure 124 bar (1800 psi)
Diameter 51 mm (2 in)
Length 235 mm (9.3 in)
Weight 0.8 kg (1.8 lb)
Volume 300 cc (18 cubic inches)
Material 316L stainless steel
Thread size .250-18 NPT
Included accessories None listed

Typical applications in Oman and the GCC

Oman and the wider GCC have many sites that need spot samples taken from pressurised lines: gas gathering and processing plants, refineries, petrochemical units, LNG and LPG facilities, and utility and water plants where gas or liquid analysis supports quality or compliance programmes. A stainless sample cylinder such as the HSSC20-1BA is used to move that sample to a laboratory without losing its integrity. The manufacturer lists petrochemical refineries, well sites, analytical laboratories, alternative fuel technology and manufacturing among the industries in which its cylinders are used.

For a plant that already uses 300 cc cylinders, the HSSC20-1BA is a straightforward replacement or addition because the size is common and the 1/4 inch NPT port matches widely used sampling valves and fittings. It also suits laboratories that run a pool of cylinders and need to add stock as old units reach their inspection dates.

Selection and compatibility notes for HSSC20-1BA

Confirm that the media is compatible with 316L stainless steel and with the valve and seal materials you plan to fit. Check that the working pressure of the sample point does not exceed the 124 bar service pressure and that any pressure relief arrangement in your procedure suits the cylinder. Remember that the manufacturer range also includes other volumes in the same series, such as 50, 75, 150, 400 and 500 cc, with different port thread sizes on some models, so verify that the suffix and size match the drawing in your sampling procedure.

The part number ends in BA and the cylinder is listed to DOT-3E. The manufacturer shows TPED versions under separate part numbers, so if the cylinder must travel under European transport rules, confirm that route with your logistics team before you order the HSSC20-1BA.

Installation and use of HSSC20-1BA

Fit the valves and fittings of your choice to the 1/4 inch NPT ports using a thread sealant or tape that suits the sampled media. Tighten to the torque recommended by the valve manufacturer and avoid overtightening on the thin cylinder neck. Leak test the assembled cylinder with an inert gas before the first field sample, purge the cylinder with the sample stream according to your procedure and fill to a pressure that stays below the 124 bar service pressure.

Maintenance and inspection

Treat the HSSC20-1BA as a pressure vessel. Inspect the outside for dents, corrosion and thread damage on every use. Keep a record of the date of each periodic inspection and test that your local regulations require for DOT-3E cylinders, and retire any unit that shows damage. Clean and dry the cylinder after sampling, particularly if the sample contained sulphur compounds or moisture, and store it with protective plugs on the ports.

Related products and ordering notes

Related items in the same manufacturer table include the HSSC20-2BA at 500 cc, the HSSC20-3BA at 400 cc and the HSSC20-4BA at 150 cc, all in 316L stainless steel with the 1/4 inch NPT thread. When you request the HSSC20-1BA, also state which valves, rupture protection or fittings you need, because none are included with this part number.

HSSC20-1BA questions in brief

The HSSC20-1BA is a 300 cc, 316L stainless steel, DOT-3E sample cylinder with 124 bar service pressure, 51 mm diameter, 235 mm length and a 1/4 inch NPT thread.

Documents and quotation

The specification table for the Luxfer 1,800 psi sampling range is published by the manufacturer on its website, and a datasheet file is not attached to this listing. To request a quotation for the HSSC20-1BA, send your RFQ to Seven Star LLC with the part number HSSC20-1BA, the quantity and the delivery location, together with any valve or fitting requirements. No prices are shown on this page.

Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Luxfer Gas Cylinders is an operating unit of the Luxfer Group (NYSE: LXFR) and a manufacturer of high-pressure gas cylinders, including aluminum cylinders for industrial and specialty gases. Its catalog spans SCBA and life-support, medical, specialty gas, calibration gas, sampling, fire extinguisher, SCUBA, beverage, alternative fuel, aerospace and defense cylinders. Luxfer cylinders are used for breathing apparatus, laboratory and analyzer gases, refinery and well-site sampling and many other portable gas applications. Seven Star LLC is an independent supplier serving Oman and the GCC and is not affiliated with the manufacturer. We help industrial, safety and laboratory buyers identify the correct cylinder part number, size and valve configuration, supporting safe and reliable gas handling.

FAQ

Questions about the Luxfer HSSC20-1BA 316L Stainless Sample Cylinder

Answers from our engineering team on installation, compatibility and integration.

01What is the Luxfer HSSC20-1BA?
It is a 300 cc sampling cylinder made from 316L stainless steel to the DOT-3E specification, with a service pressure of 124 bar (1800 psi) and a 1/4 inch NPT thread.
02What are the dimensions and weight of the HSSC20-1BA?
The manufacturer lists a diameter of 51 mm (2 in), a length of 235 mm (9.3 in) and a weight of 0.8 kg (1.8 lb), with a water volume of 300 cc (18 cubic inches).
03Does the HSSC20-1BA include valves or a carrying handle?
The manufacturer table shows no included accessories for this part number, so valves, fittings and any rupture protection must be selected and ordered separately.
04Is the HSSC20-1BA suitable for DOT or TPED transport?
This part is listed to the DOT-3E specification. TPED cylinders appear under their own part numbers in the manufacturer range, so check the transport rules for your route before ordering.
05How do I request a quotation for the HSSC20-1BA?
Send an RFQ to Seven Star LLC quoting HSSC20-1BA, the quantity needed, any valve or fitting requirements and the delivery location in Oman or the GCC.