Gewiss GW60241 IEC 309 Flush Mounting Inlet 32A 3P+E IP67

GW60241 is a straight flush-mounting inlet (a fixed appliance plug) from the Gewiss IEC 309 HP range: 32 A, 3P+E, 380-415 V, 50/60 Hz, red, reference position 6 h, with a 95 x 80 mm flange and a protection rating of IP67. It gives machines, generators and panels a built-in connection point for a mobile IEC 60309 connector.

Built-in power inlet for machines and panels

An inlet sits in the wall of an enclosure or machine and receives a mobile connector, so the equipment can be connected and disconnected without opening a terminal box. The datasheet describes the range as trailing and fixed plugs and socket-outlets for industrial use, complying with IEC 60309 and the European EN 60309 and Italian CEI 23-12 standards.

Gewiss states that sleeves and pins are obtained from solid brass bar (CuZn40Pb2: Cu 58 %, Zn 40 %, Pb 2 %) and that the terminals are anti-loosening with unlosable screws. Socket-outlets and plugs rated 63 and 125 A carry an extra pilot contact for electrical interlocking; the 32 A GW60241 does not, so use it where a plain power connection is enough.

Key features as printed in the datasheet

• Straight flush-mounting inlet, 32 A, 3P+E, 380-415 V, 50/60 Hz.
• IP67 and IK08; red body, reference position 6 h.
• Flange dimensions 95 x 80 mm.
• Solid brass sleeves and pins; anti-loosening terminals with unlosable screws.
• Screw wiring: 2.5-6 mm2 flexible, 2.5-10 mm2 rigid.
• More than 2000 operations; breaking capacity at 1.1 Un 40 A; permissible overload 42 A.
• Operating temperature -25 to +55 C.

Technical specification

Electrical

Mechanical and environmental

Selection and ordering guide

Order GW60241 when the equipment side needs a fixed 32 A three-phase inlet without neutral (3P+E). If your supply is 3P+N+E, you need a five-pole inlet instead, because poles and reference position must match the connector. Match the red colour and 6 h position with the connector you plan to use.

Derived value: at 415 V three-phase, 32 A is about 23 kVA of apparent power, at 380 V about 21 kVA (square root of 3 x U x I). These are calculations, not Gewiss ratings.

Installation and operation notes

Cut the panel opening to suit the 95 x 80 mm flange and the fixing pattern in the dimensional drawing. Tighten the terminal screws on the cable you actually use; the datasheet gives 2.5-6 mm2 flexible capacity.

IP67 applies to the inlet when a connector is correctly engaged or the cover is closed; keep the sealing surfaces clean. Do not exceed -25 to +55 C at the inlet body.

Practical check before ordering: confirm that the cut-out in your panel or machine frame can host the 95 x 80 mm flange and that the cable on the machine side can be terminated at 2.5 to 10 mm2. Because the inlet has no neutral pole, a 5-wire supply cannot be connected through it; the two-pole difference is the most common ordering mistake with red three-phase connectors, so quote the pole count together with the order code when you ask for a price.

Applications in Oman and the GCC

Inlets are used on generators, welding sets, mobile compressors, marine and quay-side equipment, concrete plant, test benches and temporary distribution kits that must be connected to a site supply by a trailing cable.

On Gulf sites, red IEC 60309 inlets are common for 380-415 V equipment; choose IP67 versions when equipment stands outdoors, in washdown zones or in dusty yards.

Installation and selection notes

The GW60241 inlet is fitted through a panel cut-out with its 95 x 80 mm flange, then connected inside the enclosure to the machine supply. Because it is a 32 A, 3P+E device at 380-415 V without a neutral, check that the machine has no single-phase loads needing a neutral. Match the plug type and the 6 h reference position with the mobile connector, and tighten the terminals to the torque in the instruction sheet.

Information needed for a quotation

Send the code GW60241, the quantity and the delivery location in Oman or the GCC, and add any matching mobile plugs or cable sets to the request.

Documents and supply information

The manufacturer data sheet is attached to this page and should be read together with the project specification before a purchase is confirmed. Ratings, dimensions and protection classes are quoted as printed on that sheet. Lead time, stock position and certificates available with the shipment are confirmed in the quotation, and we supply to Oman and the wider GCC region for industrial, utility and building services projects.

Compatible accessories and related items

Mating mobile connector: the 32 A, 3P+E straight connector of the HP range (ask for the matching code). Other family items: the 3P+N+E plug GW60042H, connector GW62042H and angled socket-outlet GW62220H.

Frequently asked questions

Is GW60241 a plug or a socket?

It is a straight flush-mounting inlet, a fixed plug-type device that receives a mobile connector.

What are the ratings?

32 A, 3P+E, 380-415 V, 50/60 Hz, IP67, IK08, red, 6 h.

What flange size does it need?

The datasheet states flange dimensions of 95 x 80 mm.

What wire sizes fit the terminals?

2.5-6 mm2 flexible and 2.5-10 mm2 rigid cable.

Is Seven Star LLC a Gewiss distributor?

No. Seven Star LLC is not a Gewiss distributor; it is an independent Muscat-based supplier that quotes Gewiss products on request.

Documents and quotation

Need GW60241? The Gewiss product data sheet is attached to this listing. Seven Star LLC (independent supplier, Muscat) can quote the item and arrange supply on request; list quantity and site location in your enquiry. Verify the code, dimensions and approvals in the document before ordering. Other products are in the category page.