Brand:

Pedrollo WR In-Line Close-Coupled Circulation Pump

Description

Pedrollo WR pump explained

The Pedrollo WR is an in-line close-coupled centrifugal pump rated up to 700 l/min (42 m³/h) and up to 26 m of head, for liquid between -10 and +110 °C at up to 10 bar (PN10). Seven Star LLC supplies the Pedrollo WR in Oman and the GCC as an independent supplier in Muscat.

WR 40/125 and WR 50/125 combine the port size and the nominal impeller size in mm; the suffixes SA, SB, A, B and C identify the power and impeller variants listed in the datasheet. WR 40/125-SB is 0.55 kW at 18.7 m and WR 50/125B is 1.5 kW at 20.5 m.

WR technical specifications

Parameter Specification
Manufacturer / part number Pedrollo / WR
Flow rate up to 700 l/min (42 m³/h)
Head up up to 26 m
Manometric suction head up to 7 m
Liquid temperature between -10 °C and +110 °C
Ambient temperature between -10 °C and +40 °C
Maximum working pressure 10 bar (PN10)
Motor 2 poles
Ingress protection rating IP X4
Pump housing Cast iron
Impeller Stainless steel AISI 304
Shaft Stainless steel AISI 431
Pump cover Cast iron

The values above come from the manufacturer technical data for the series. Individual models inside the WR range differ in power, head and current, so always confirm the exact model code before ordering.

How the WR works and what limits it

Cast iron body and cover, AISI 304 impeller, AISI 431 shaft, IP X4, ambient -10 to +40 °C, suction up to 7 m.

An in-line close-coupled pump has the suction and delivery ports on one axis so it can be installed straight into a pipe run. The impeller is mounted directly on the motor shaft, which keeps the unit compact and avoids a coupling. Liquid enters axially, is accelerated by the impeller and leaves through the volute. The pump is rated for the liquid temperature stated on the data sheet, so it suits closed loops with warm or hot water as well as cold circuits, provided the liquid is clean and compatible with the pump materials.

Selecting between the two port sizes is largely a matter of flow. The WR 40/125 models are listed for flows up to 18 m³/h with 0.55 and 0.75 kW motors, while the WR 50/125 family covers flows to 42 m³/h with motors from 0.55 kW to 1.5 kW. For a hot circuit near the upper temperature limit, confirm the mechanical seal type and the pressure of the system with us, and remember that the working pressure limit of 10 bar applies to the pump body.

The WR combines a cast iron body and cover with a stainless steel AISI 304 impeller, and its main advantage in a circuit is the temperature range: from -10 up to +110 °C, with a 10 bar (PN10) pressure rating. Two port sizes appear in the datasheet, WR 40/125 and WR 50/125, with 0.55 kW to 1.5 kW motors and heads from about 14 m to 22 m at the first table point. The flow range reaches 700 l/min for the WR 50/125 line.

Because the pump is in-line, it is easy to retrofit into a pipe run, but pipe supports and vibration isolation still matter. Keep the isolating valves close to the pump for servicing, and use the manufacturer manual for the mounting position and the ventilation of the motor.

WR models and performance data

Model Rated power P2 Head at first table point (50 Hz)
WRm 40/125-SB 0.55 kW / 0.75 HP 18.7 m
WRm 40/125-SA 0.75 kW / 1 HP 22.4 m
WRm 50/125-SB 0.55 kW / 0.75 HP 14 m
WRm 50/125B 1.5 kW / 2 HP 20.5 m

The heads in this table are read from the first point of the manufacturer 50 Hz performance table and fall as flow increases, so use the full curve for the real duty point. Where a 60 Hz version is needed, ask us: the manufacturer states that 60 Hz motors are available on request for many models.

Where the WR fits: related Pedrollo pumps

PV, F-INOX.

Selecting a WR pump: checklist

  • Port size
  • Impeller
  • Liquid temperature
  • Phase
  • Mounting

Installing and maintaining the WR

Install the pump in a horizontal or vertical pipe with the motor shaft horizontal where specified, leaving space above and beside the motor for cooling and servicing. Support the pipework so its weight does not load the pump casing, fit isolating valves on both sides and a strainer upstream. Vent the casing and the circuit before starting, since trapped air reduces flow and can damage the seal. Insulate the pipes but leave the motor free to breathe. In heating circuits, check the expansion vessel and the circuit pressure, and in cooling circuits protect the terminal box from condensation. Check the seal for dripping at each service visit.

WR applications in Oman and the GCC

Heating, air conditioning, cooling and circulation systems.

Chilled-water and hot-water loops in Gulf buildings run almost year round, so circulation pumps accumulate operating hours quickly. Keep the liquid clean with a strainer, use the right glycol or inhibitor, and check seal condition at each maintenance round. Outdoor installations should be shaded and the terminal box kept dry.

Information to send with your WR RFQ

  • Flow rate and head required in the circuit
  • Liquid and its temperature range, glycol content and additives
  • Port size or flange standard and mounting position
  • Supply: phase, voltage and frequency
  • Quantity and any spare seals or counter-flanges requested

Documents and quotation

The manufacturer datasheet for the WR is attached on this page, and the performance tables in it should be checked against your duty point. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer.

Send the model code, quantity, voltage and frequency and the duty point, and we will confirm availability and prepare a quotation for Oman and the GCC.

Datasheets & Documents
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Pedrollo is an Italian manufacturer of electric pumps, founded in 1974 by Silvano Pedrollo and headquartered in San Bonifacio, near Verona, where its plant covers more than 150,000 square metres. The company exports to over 160 countries through ten commercial branches, starting with Pedrollo France in 1987. Its pumps are used for domestic water supply, irrigation, boreholes, pressure boosting and drainage.

Seven Star LLC is an independent supplier in Muscat. We list Pedrollo pumps for homes, farms and contractors in Oman and the GCC.

Pedrollo company profile

Founded 1974, by Silvano Pedrollo
Headquarters San Bonifacio, Verona, Italy
Ownership Pedrollo family
Reach Exports to over 160 countries through ten commercial branches
Product families PKm peripheral pumps, CP and F centrifugal pumps, JSWm self-priming jet pumps, 4SR and 6SR submersible borehole pumps, TOP and VXm drainage pumps, HF high-flow pumps, pressure booster sets

Milestones

  • 1974: Silvano Pedrollo founds the company.
  • 1987: Pedrollo France, the first foreign branch, opens.
  • 2009: Pedrollo acquires a majority stake in Saci Pumps.

Pedrollo product series

Surface pumps include the CP close-coupled centrifugal pump from 0.25 to 2.2 kW, the 2CP twin-impeller pump from 1.1 to 11 kW, the F EN 733 close-coupled pump, the NGA open-impeller pump for dirty water and the HT vertical multistage pump.

Submersible pumps include the 4SR and 6SR borehole pumps for 4 and 6 inch wells and the VX vortex sewage pump.

Close-coupled centrifugal pumps suit clean water transfer and boosting, twin-impeller 2CP pumps give higher head at moderate flow, and the open-impeller NGA handles water with some solids. Submersible 4SR and 6SR pumps are matched to the well diameter, flow and depth, and the VX vortex pump passes solids in sewage and drainage.

Where Pedrollo pumps are used

Water supply and pressure boosting, irrigation, wells, tank transfer, and drainage and sewage.

Pedrollo products we list

Family Examples
Pumps 2CP Twin-Impeller Centrifugal Pump 1.1-1…, 4SR 4-Inch Submersible Borehole Pump, 6SR 6-Inch Submersible Borehole Pump, CP Close-Coupled Centrifugal Pump 0.25-2…, F EN 733 Close-Coupled Centrifugal Pump, HT Vertical Multistage Centrifugal Pump, NGA Open-Impeller Centrifugal Pump for D…

Ordering Pedrollo pumps: what we need

Send the model or the flow, head and liquid, the power supply and the well diameter or installation type.

Facts checked against Pedrollo's own history page (pedrollo.com), October 2026.

FAQ

Questions about the Pedrollo WR In-Line Close-Coupled Circulation Pump

Answers from our engineering team on installation, compatibility and integration.

01What is the maximum liquid temperature for the WR?
The WR is rated for liquids between -10 and +110 °C at up to 10 bar (PN10), which is higher than most clean-water pumps in the Pedrollo range.
02What systems is the WR designed for?
Pedrollo lists civil and industrial uses such as heating, air conditioning, cooling and circulation systems with clean liquids.
03Can the WR be installed vertically?
In-line pumps are normally installed in horizontal or vertical pipework, but check the mounting position with the manual for your model.
04Does the WR need a strainer?
A strainer upstream protects the seal and the impeller from debris in the circuit.
05Is the WR suitable for hot water?
Yes, up to the temperature limit on the data sheet, provided the liquid is clean.