Brand:

Pedrollo 4HR Stainless 4-Inch Borehole Pump

Description

Pedrollo 4HR pump explained

The Pedrollo 4HR is a 4-inch submersible borehole pump in precision-cast stainless steel AISI 304, rated up to 420 l/min (25.2 m³/h) and up to 176 m of head. Seven Star LLC supplies the 4HR in Oman and the GCC as an independent supplier in Muscat.

4HR 10, 14 and larger flow classes with stage numbers, for instance 4HR 10/5 is 0.75 kW at 28.5 m, 4HR 10/15 is 2.2 kW at 86 m and 4HR 10/28 is 4 kW at 161 m. 4HRm is single-phase.

4HR technical specifications

Parameter Specification
Manufacturer / part number Pedrollo / 4HR
Flow rate up to 420 l/min (25.2 m³/h)
Head up up to 176 m
Liquid temperature up to +40 °C
Maximum sand content 100 g/m3
Maximum operating depth below water level – 200 m with 4PD motors – 300 m with 4PS motors
Motor 2 poles
Ingress protection rating IP 68
Delivery port Precision casted stainless steel AISI 304
Impellers Precision casted stainless steel AISI 304
Diffusers Precision casted stainless steel AISI 304
Shaft Stainless steel AISI 304
Motor bracket Precision casted stainless steel AISI 304

The values above come from the manufacturer technical data for the series. Individual models inside the 4HR range differ in power, head and current, so always confirm the exact model code before ordering.

How the 4HR works and what limits it

Delivery port, impellers, diffusers and motor bracket are precision-cast AISI 304, shaft AISI 304. Sand to 100 g/m³, depth 200 m with 4PD motors and 300 m with 4PS motors.

A borehole pump is a long, slim assembly in which a multistage hydraulic end sits below a submersible motor, and the whole unit hangs in the well on the rising main. Water enters through the suction strainer, passes through the stages in series and leaves through the delivery port at the top. Because the diameter is limited by the well casing, the head is built by adding stages, which is why the models are identified by a flow class and a stage number. The sand content in the water and the depth of submergence are the two limits that matter most for service life.

The 4HR range is a stainless steel borehole pump with precision-cast hydraulic parts. The datasheet shows two flow classes in the table, the 4HR 10 and the 4HR 14, with many stage options: for instance the 4HR 10 runs from 10/5 at 0.75 kW up to 10/28 at 4 kW, and the 4HR 14 starts at 14/6 at 1.1 kW. Single-phase 4HRm versions are listed for the smaller sizes, and the larger sizes are three-phase only.

The two depth ratings relate to the motor: 200 m with 4PD motors and 300 m with 4PS motors, so the motor type must be stated on the order. Check the casing diameter and the well depth, and allow for the length of the pump plus motor when deciding the setting depth.

4HR models and performance data

Model Rated power P2 Head at first table point (50 Hz)
4HRm 10/5 0.75 kW / 1 HP 28.5 m
4HRm 10/15 2.2 kW / 3 HP 86 m
4HR 10/28 4 kW / 5.5 HP 161 m
4HRm 14/6 1.1 kW / 1.5 HP 31 m

The heads in this table are read from the first point of the manufacturer 50 Hz performance table and fall as flow increases, so use the full curve for the real duty point. Where a 60 Hz version is needed, ask us: the manufacturer states that 60 Hz motors are available on request for many models.

Where the 4HR fits: related Pedrollo pumps

Smaller: 3SR; larger: 6HR.

Selecting a 4HR pump: checklist

  • Flow class
  • Stage number
  • Depth
  • Motor type
  • Sand

Installing and maintaining the 4HR

Check the well diameter, depth, the dynamic water level and the sand content before choosing the pump. Fit a strainer or inlet screen as required, lower the pump on a rising main or rope with the cable clamped at intervals, and keep the pump below the dynamic water level with the margin given in the manual. Fit a non-return valve in the delivery line, a motor protection device and, if the well can run low, dry-run protection. Set the first start-up with the delivery valve partly closed and open it gradually until the flow stabilises and the water runs clear. Keep a logbook of current draw and flow so that wear or a falling water table can be detected early.

4HR applications in Oman and the GCC

Industrial, civil and agricultural use: pressure tanks, irrigation, boosting and fire fighting.

Groundwater in Oman varies widely in salinity, temperature and sand content, and water tables may fall over a season. Ask for a recent analysis of the well, record the dynamic level after pumping for several hours, and choose a pump whose stated sand limit and depth rating suit that data. Corrosive or very saline water needs a material check before ordering.

Information to send with your 4HR RFQ

  • Well diameter, total depth, static and dynamic water levels
  • Required flow rate and total head at the surface, including pipe losses
  • Water quality: sand content, temperature and chemistry
  • Supply: voltage, frequency, phase and control or starter type
  • Rising-main material and size, cable length and quantity of pumps

Storage, handling and spares for the Pedrollo 4HR

Store the Pedrollo 4HR in a dry, covered place and keep it in its packaging until installation. If the pump is stored for a long time, turn the shaft by hand from time to time where the design allows it, so that seals do not stick. In Oman and the GCC, protect the motor and cable from direct sun and sand before installation.

  • Check the pump nameplate against the duty point and the power supply before installation.
  • Flush the pipework before connecting the pump, so that welding debris or sand does not enter the hydraulic parts.
  • Never run the pump dry; fit level control or dry-running protection where the application needs it.
  • Keep a spare mechanical seal kit and, for submersible models, a spare cable joint kit for planned maintenance.

When you send an RFQ for the Pedrollo 4HR, state the flow, head, liquid and power supply. With this information the right model and any spare parts can be confirmed together.

Documents and quotation

The manufacturer datasheet for the 4HR is attached on this page, and the performance tables in it should be checked against your duty point. Seven Star LLC is an independent supplier in Muscat and is not affiliated with the manufacturer.

Send the model code, quantity, voltage and frequency and the duty point, and we will confirm availability and prepare a quotation for Oman and the GCC.

Other Models in the Pedrollo Bore Range

Seven Star LLC supplies models from the Pedrollo Bore range in Oman and the GCC. Compare the related models below and request a quote for the one that matches your application.

ModelCategory
Pedrollo 3SR 3-Inch Submersible Borehole PumpCentrifugal PumpsView details
Pedrollo 4HR Stainless 4-Inch Borehole PumpCentrifugal PumpsYou are viewing this model
Pedrollo 6HR Stainless 6-Inch Borehole PumpCentrifugal PumpsView details
Pedrollo UP Multistage Submersible Pump 20 m DepthCentrifugal PumpsView details
Pedrollo NK Multistage Submersible Pump for TanksCentrifugal PumpsView details
Datasheets & Documents
Reviews (0)

Reviews

There are no reviews yet.

How would you rate this product?

It takes about 10 seconds — just tap a star. Your email is never published.

About brand

Pedrollo is an Italian manufacturer of electric pumps, founded in 1974 by Silvano Pedrollo and headquartered in San Bonifacio, near Verona, where its plant covers more than 150,000 square metres. The company exports to over 160 countries through ten commercial branches, starting with Pedrollo France in 1987. Its pumps are used for domestic water supply, irrigation, boreholes, pressure boosting and drainage.

Seven Star LLC is an independent supplier in Muscat. We list Pedrollo pumps for homes, farms and contractors in Oman and the GCC.

Pedrollo company profile

Founded 1974, by Silvano Pedrollo
Headquarters San Bonifacio, Verona, Italy
Ownership Pedrollo family
Reach Exports to over 160 countries through ten commercial branches
Product families PKm peripheral pumps, CP and F centrifugal pumps, JSWm self-priming jet pumps, 4SR and 6SR submersible borehole pumps, TOP and VXm drainage pumps, HF high-flow pumps, pressure booster sets

Milestones

  • 1974: Silvano Pedrollo founds the company.
  • 1987: Pedrollo France, the first foreign branch, opens.
  • 2009: Pedrollo acquires a majority stake in Saci Pumps.

Pedrollo product series

Surface pumps include the CP close-coupled centrifugal pump from 0.25 to 2.2 kW, the 2CP twin-impeller pump from 1.1 to 11 kW, the F EN 733 close-coupled pump, the NGA open-impeller pump for dirty water and the HT vertical multistage pump.

Submersible pumps include the 4SR and 6SR borehole pumps for 4 and 6 inch wells and the VX vortex sewage pump.

Close-coupled centrifugal pumps suit clean water transfer and boosting, twin-impeller 2CP pumps give higher head at moderate flow, and the open-impeller NGA handles water with some solids. Submersible 4SR and 6SR pumps are matched to the well diameter, flow and depth, and the VX vortex pump passes solids in sewage and drainage.

Where Pedrollo pumps are used

Water supply and pressure boosting, irrigation, wells, tank transfer, and drainage and sewage.

Pedrollo products we list

Family Examples
Pumps 2CP Twin-Impeller Centrifugal Pump 1.1-1…, 4SR 4-Inch Submersible Borehole Pump, 6SR 6-Inch Submersible Borehole Pump, CP Close-Coupled Centrifugal Pump 0.25-2…, F EN 733 Close-Coupled Centrifugal Pump, HT Vertical Multistage Centrifugal Pump, NGA Open-Impeller Centrifugal Pump for D…

Ordering Pedrollo pumps: what we need

Send the model or the flow, head and liquid, the power supply and the well diameter or installation type.

Facts checked against Pedrollo's own history page (pedrollo.com), October 2026.

FAQ

Questions about the Pedrollo 4HR Stainless 4-Inch Borehole Pump

Answers from our engineering team on installation, compatibility and integration.

01What depth can the 4HR operate at?
The maximum operating depth below water level is 200 m with 4PD motors and 300 m with 4PS motors.
02What is the 4HR made of?
The delivery port, impellers, diffusers and motor bracket are precision-cast AISI 304 stainless steel, with an AISI 304 shaft.
03Can the 4HR run dry?
No. The pump should stay below the dynamic water level, and dry-run protection is advised for wells that may be drawn down.
04What should I check before ordering the 4HR?
Well diameter, depth, dynamic level, sand content and the duty point at the surface.
05Does the 4HR need a non-return valve?
A non-return valve in the delivery line prevents back-flow and water hammer when the pump stops.