ABB ACS880-01-065A-5 ACS880-01 30 kW Frame R5 AC Drive

30 kW ABB ACS880-01-065A-5 drive for process and machine control

A 65 A rating, a frame R5 housing and a 380 to 500 V input define the ABB ACS880-01-065A-5. ABB positions the ACS880 single drive for demanding industrial duty and offers direct torque control in its primary control program.

Typical uses in oil, gas, water and fabrication plants include centrifugal pumps, extruders, hoists and test benches. The drive ships as IP21 (UL Type 1) unless a plus code selects another construction.

Technical specifications

What to size around 065A A

Overload capability is expressed through duty classes. Here the heavy-duty class carries 52 A (22 kW), the light-duty class 62 A (30 kW) and nominal use 65 A (30 kW), all at 400 V.

The -5 voltage code also covers 480 V and 500 V networks: 65 A and 37 kW nominal at 500 V, or 50 hp light duty and 40 hp heavy duty by the UL table at 480 V.

Frame R5 weighs 22.8 kg in IP21 form and measures 203 mm wide, 732 mm high and 274 mm deep including the cable entry box. Cooling air demand is 280 m3/h; typical losses reach 715 W, which the cabinet or room must carry away.

Fusing options are 100 A gG (OFAF000H100), 125 A aR (170M1568) or UL class T JJS-90. The IEC copper cable entry is 3×35 mm2 and the UL conductor is 4 AWG-kcmil. This frame has no brake chopper as standard; ABB lists the +D150 brake chopper as a factory option.

Keep the motor cable within 300 m (frame R5). The drive works on TN and IT networks, with a 65 kA short-circuit rating when protected by the listed fuses.

Reading the ACS880-01-065A-5 order code

In ACS880-01-065A-5, ACS880 is the series, 01 the wall-mounted single drive, 065A the size and -5 the voltage range. Plus codes follow: +B056 gives IP55, +E200 and +E202 select EMC filters, +D150 adds a brake chopper and +C131 adds vibration dampers. Quote every plus code you need.

Selection checks for the 065A-5 drive

Begin with the motor nameplate and the load. Compare the motor full-load current with the duty class that matches the application: a centrifugal pump or fan usually fits a light-duty rating, while a hoist, extruder or conveyor that starts under load points toward the heavy-duty figure. Confirm the supply voltage at site, the network earthing system and the prospective short-circuit level, and decide whether the application regenerates energy that would need braking.

Next look at the installation: wall space in a panel or plant room, cable routes, the length of the motor cable, and whether EMC requirements on site call for one of the filter plus codes listed above. Listing these points in the enquiry avoids ordering a drive that needs changes after it arrives.

Installation and commissioning

Mount the drive vertically on a solid, non-flammable surface with the clearances given in the ABB hardware manual so cooling air can flow freely. Use the fuse types listed for this frame, size cables for the actual current and route the motor cable separately from control and signal cabling. Shielded motor cable with correct earthing at both ends helps reduce interference with nearby instruments.

Before first energisation, check insulation resistance of the motor and cable as the manual instructs, verify all terminations and confirm that the safe torque off circuit is wired as the safety design requires. Use the control panel start-up assistant to enter motor data, run the motor identification routine where the mechanics allow it, and then set ramps, limits and the control source. Save a parameter backup once the drive runs correctly and record it with the loop documentation.

Heat, dust and humidity in Omani plant rooms

The typical losses and cooling air figures in the table become critical in Oman and the GCC, where summer ambient temperatures in outdoor kiosks and unventilated rooms can approach or exceed the range in which the drive runs without derating. Size room ventilation or panel cooling for the heat the drive and other equipment release, and keep inlet air as clean and cool as practical. Avoid placing the drive where hot exhaust from other equipment feeds its intake.

Fine dust settles on heat sinks and reduces cooling, and humid coastal air can lead to condensation when equipment cools overnight. Filtered ventilation, sealed cable entries and the IP55 construction option are worth considering for dusty or damp sites, and the coated boards listed in the specification help in harsh atmospheres.

Routine maintenance

Follow the ABB preventive maintenance schedule for the frame. In practice that means periodic cleaning of air paths, checking that cooling airflow is unobstructed, re-tightening power terminals at the recommended intervals and reviewing the fault and event logs for recurring warnings. Keep a copy of the current parameter set so a replacement drive can be configured quickly if needed.

Documents and quotation

The catalogue attached to this page and the abb.com record for ACS880-01-065A-5 document the type. Neighbouring products sit under AC Drives, with the family overview on the ACS880-01 page.

Confirm voltage band, frame, plus codes and control panel with us before ordering. Seven Star LLC is an independent supplier in Muscat; stock and lead time are stated in the quotation.