Siemens 6XV1875-5AH50 N-Connect Antenna Connection Cable, 5m

Overview

The Siemens 6XV1875-5AH50 is a factory pre-assembled antenna connection cable terminated with N-Connect male connectors at both ends, supplied in a 5 meter length for use with SIMATIC NET Industrial Wireless LAN and mobile radio equipment. Rather than requiring a technician to hand-terminate coaxial cable on site, the 6XV1875-5AH50 arrives ready to connect, eliminating a common source of poor RF performance caused by inconsistent field connector assembly.

Seven Star LLC, an authorized Siemens partner in Oman and the GCC, supplies genuine Siemens 6XV1875-5AH50 antenna cables to system integrators running SCALANCE antenna feeds between access points and remotely mounted antennas. Every cable shipped is sourced through verified Siemens distribution channels, preserving the RF performance guarantees that a genuine, factory-tested assembly provides over a generic aftermarket cable.

Measurement and Operating Principle

The 6XV1875-5AH50 carries radio frequency signal between a SCALANCE access point’s N-Connect antenna port and a remotely mounted external antenna, maintaining a 50Ω impedance match along its full 5 meter length to minimize reflection loss and standing wave ratio degradation. The cable is rated for frequencies up to 6 GHz, covering the 2.4 GHz, 5 GHz, and 6 GHz bands used by current-generation SCALANCE IWLAN hardware including Wi-Fi 6E devices.

Cable attenuation is specified at approximately 0.53 dB/m at 2.4 GHz, rising at higher frequencies, so installers calculating a wireless link budget can account for the exact signal loss the 6XV1875-5AH50 introduces between radio and antenna. Because both ends terminate in N-Connect male connectors, the cable is typically paired with an antenna presenting an N-Connect female interface, such as the Siemens ANT795 series.

Engineering Design

The Siemens 6XV1875-5AH50 uses a braided shield of tin-plated copper wires over a polyethylene foam dielectric, with a 6.3mm outer diameter and 1.4mm inner conductor, a construction chosen to balance flexibility for routing through cable trays and conduit against the shielding performance needed to reject electromagnetic interference in an industrial environment. The cable jacket is silicone-free and halogen-free, and finished in a pastel turquoise color that makes SIMATIC NET antenna cabling visually distinct from other plant cabling during maintenance.

Rated IP68 and for an ambient temperature range of −40°C to +80°C, the 6XV1875-5AH50 is built for the same outdoor and extended-environment conditions as the SCALANCE EEC device family it is commonly installed alongside, making it suitable for exposed cable runs between an outdoor-mounted access point and an antenna positioned for optimal coverage.

Key Features

• Factory pre-assembled 5 meter N-Connect male/male antenna connection cable
• 50Ω impedance matched for minimal reflection loss on SCALANCE antenna feeds
• Rated for frequencies up to 6 GHz, covering 2.4/5/6 GHz IWLAN bands
• Braided tin-plated copper shield for electromagnetic interference rejection
• IP68-rated, silicone-free and halogen-free jacket construction
• Extended −40°C to +80°C ambient temperature rating for outdoor installation
• Distinctive pastel turquoise jacket for easy identification during maintenance
• Genuine Siemens SIMATIC NET sourcing avoids field-termination RF performance risk

Industrial Applications

The Siemens 6XV1875-5AH50 is used to connect SCALANCE WAM and W700-series access points to remotely mounted external antennas across ports, refineries, mining sites, and large manufacturing yards, wherever the optimal antenna mounting position is separated from the access point itself. Its extended temperature and IP68 rating make it a natural pairing for outdoor SCALANCE EEC hardware deployed across the wide climate range typical of GCC industrial sites.

Seven Star LLC supports outdoor SCALANCE wireless installations across Oman’s port, oil and gas, and mining sectors, supplying the 6XV1875-5AH50 antenna cable to projects in Muscat, Sohar, and Salalah alongside compatible access points and antennas. As an authorized Siemens partner, Seven Star LLC can advise on cable length selection and expected attenuation for GCC customers planning a wireless link budget.

Technical Specifications

Why Choose Seven Star LLC for Siemens Antenna Connection Cables

An antenna connection cable’s length, connector type, and signal loss characteristics matter more than they might appear, since running an industrial WLAN antenna too far from its access point on the wrong cable grade can degrade signal strength enough to undermine coverage that was otherwise planned correctly. Seven Star LLC confirms the correct N-Connect cable length and connector configuration against your actual antenna placement and access point distance before order confirmation, backed by our authorized Siemens partnership across Oman and the wider GCC. We also support wireless network installations across Sohar and Salalah with complete cable and connector kitting alongside access points and antennas, so a wireless network project ships as one coordinated package rather than a series of separate orders, and our team can advise on cable routing practices that minimize signal loss in longer antenna runs across large facilities.

Request a Quote

Contact Seven Star LLC for pricing and availability on the Siemens 6XV1875-5AH50 N-Connect antenna connection cable. Our team in Muscat serves customers across Oman and the GCC with genuine Siemens SIMATIC NET wireless accessories.

Related Products

• Blackview Rock 1 Pro Rugged Smartphone
• Huawei MA5616 AC Chassis with CCUB Main Control Board and GP1A Uplink
• QLSAMBAN – Siemens APACS / QUADLOG Standard Analog Module (ROM 3.0)
• IKUSI BAS-700 Base Plate for CLASS A Modules
• Siemens 6GK1503-2CC00 SIMATIC NET PROFIBUS Optical Link Module (OLM/G11-1300)
• FiberHome Fonsweaver 780B O2500-4 Optical Line Unit